Makita LS1214 Manual De Instrucciones página 22

MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
WARNING:
• Always be sure that the blade is sharp and clean for the
best and safest performance.
Adjusting the cutting angle
This tool is carefully adjusted and aligned at the factory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
1. Miter angle
Push the carriage toward the guide fence and tighten the
knob to secure the carriage.
Loosen the grip which secures the turn base. Turn the
turn base so that the pointer points to 0° on the miter
scale. Then turn the turn base slightly clockwise and
counterclockwise to seat the turn base in the 0° miter
notch. (Leave as it is if the pointer does not point to 0°.)
Loosen the hex bolts securing the guide fence using the
socket wrench. (Fig. 48)
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin. Square the side of the
blade with the face of the guide fence using a triangular
rule, try-square, etc. Then securely tighten the hex bolts
on the guide fence in the order from the right side.
(Fig. 49)
Make sure that the pointer points to 0° on the miter scale.
If the pointer does not point to 0°, loosen the screw which
secures the pointer and adjust the pointer so that it will
point to 0°. (Fig. 50)
2. Bevel angle
1) 0° bevel angle
Push the carriage toward the guide fence and
tighten the knob to secure the carriage. Lower the
handle fully and lock it in the lowered position by
pushing in the stopper pin. Loosen the lever at the
rear of the tool. Make sure that the arm is locked.
(Fig. 51)
Turn the hex bolt on the left side of the arm two or
three revolutions counterclockwise. Turn the hex bolt
on the right side of the arm two or three revolutions
counterclockwise to tilt the blade to the left. (Fig. 52)
Carefully square the side of the blade with the top
surface of the turn base using the triangular rule, try-
square, etc. by turning the hex bolt on the right side
of the arm clockwise. Turn the hex bolt on the left
side of the arm clockwise as far as it will go. Then
tighten the lever securely. (Fig. 53)
Make sure that the two pointers on the arm point to
each 0° on the bevel scale on the arm holder. If they
do not point to 0°, loosen the screws which secure
the pointers and adjust them so that they will point to
0°. (Fig. 54)
2) 45° bevel angle (Fig. 55)
Adjust the 45° bevel angle only after performing 0°
bevel angle adjustment. To adjust left 45° bevel
angle, loosen the lever and tilt the blade to the left
fully. Make sure that the pointer on the arm points to
45° on the bevel scale on the arm holder. If the
pointer does not point to 45°, turn the left 45° bevel
angle adjusting bolt on the side of the arm holder
until the pointer points to 45°.
22
To adjust right 45° bevel angle, perform the same
procedure described above.
Adjusting for smooth beveling action (Fig. 56)
The hex lock nut holding together the arm and arm
holder has been factory adjusted to assure smooth bev-
eling action and to guarantee precise cutting. Do not
tamper with it. Should looseness develop at the arm and
arm holder connection, tighten the hex lock nut using a
wrench.
Adjusting the position of laser line (Fig. 57 & 58)
For model LS1214L only
WARNING:
• As the tool is plugged when adjusting the position of
laser line, take a full caution especially at switch action.
Pulling the switch trigger accidentally cause an acci-
dental start of the tool and personal injury.
CAUTION:
• Never look into the laser beam directly. Direct laser
beam causes damage to your eyes.
• Never apply a blow or impact to the tool. A blow or
impact causes the incorrect position of laser line, dam-
age to the laser beam emitting part or a short life of the
tool.
When adjusting the laser line appears on the left side
of the saw blade
1
1 Screw to change the movable range of the adjusting
screw
2 Adjusting screw
3 Hex wrench
4 Laser line
5 Saw blade
When adjusting the laser line appears on the
right side of the saw blade
1
1 Screw to change the movable range of the adjusting
screw
2 Saw blade
3 Laser line
For both adjustments, do as follows.
1. Make sure that the tool is unplugged.
2. Draw the cutting line on the workpiece and place it
on the turn table. At this time, do not secure the
workpiece with a vise or similar securing device.
2
4
5
3
2
3