Intuvia Eshift Basic Settings Menu; Error Code Indication - Bosch Intuvia eShift Manual Del Usuario

4 |
eShift with Shimano Di2
For Shimano eShift you use the Shimano control lever to shift
gears.
The engaged gear will be shown briefly on the display whenev-
er the gear of the gear hub is shifted.
The drive unit recognises the gear shift and briefly reduces
the motor assistance level as a result of it, which means the
gear can also be shifted at any time under load or on a hill.
The information menu for displaying the engaged gear of the
gear hub is as follows.
Information menu
– "Clock": Current time
– "Max. speed": Maximum speed achieved since the last
reset
– "Avg. speed": Average speed achieved since the last reset
– "Trip time": Trip time since the last reset
– "Range": Estimated range of the available battery-pack
charge (for constant conditions such as assistance level,
route profile, etc.)
– "Odometer": Display of the total distance travelled with
the eBike (cannot be reset)
– "Gear": Currently engaged gear of the automatic gear hub
is displayed.
– "Trip distance": Distance covered since the last reset

Intuvia eShift basic settings menu

To go to the basic settings menu, simultaneously press the
"RESET" button and the "i" button until "Configuration" ap-
pears in the text display.
The following basic settings are available:
– "Clock": The current time can be set here. Pressing and
holding the setting buttons fast-forwards the setting
speed.

Error Code Indication

Code Cause
580 Software version error
591 Configuration error
592 Incompatible component
593 Configuration error
595, 596 Configuration error
7xx Transmission error
X 275 007 BAI | (23.1.15)
– "Wheel circum.": You can change this value pre-set by the
manufacturer by ± 5 %. This value is displayed only when
the on-board computer is in the holder.
– "English": You can change the language of the text indica-
tions. You can choose between German, English, French,
Spanish, Italian, Dutch and Danish.
– "Unit km/mi": The speed and distance can be displayed
either in kilometres or miles.
– "Time format": The time can be displayed either in the
12 hour or 24 hour format.
– "Shift recom. on/off": You can switch the indication of a
shift recommendation on and off.
– "Power-on hours": Indicates the total travel duration with
the eBike (not changeable).
– "Gear calibration" (only NuVinci H|Sync): Here you can
calibrate the continuously variable transmission. Confirm
the calibration by pressing the "Bike lights" button. Then
follow the instructions.
In the event of an error, it can also be necessary to perform
calibration when riding. In this case, you also confirm the
calibration by pressing the "Bike lights" button and then
follow the instructions on the display.
– "Displ. vx.x.x.x": This is the software version of the dis-
play.
– "DU vx.x.x.x": This is the software version of the drive
unit. This value is displayed only when the on-board com-
puter is in the holder.
– "Bat vx.x.x.x": This is the software version of the battery
pack. This value is displayed only when the on-board com-
puter is in the holder.
– "Gear vx.x.x.x": This is the software version of the auto-
matic transmission. This value is displayed only when the
on-board computer is in the holder.
To exit the function and save a changed setting, press the
"RESET" button for 3 s.
Corrective Measure
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Switch off the eBike system. Remove the battery pack and reinsert it.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Insert a compatible display. If the problem persists, contact your Bosch
eBike dealer.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Check the wiring to the transmission and restart the system. If the prob-
lem persists, contact your Bosch eBike dealer.
Please observe the operating instructions provided by the transmission
manufacturer.
Bosch Power Tools