Inglesina QUAD Manual De Instrucciones página 28

ATTACHING THE HOOD
fig. 23 Fasten the press studs to the carrycot structure.
fig. 24 Wrap the hood (C1) around the handle and secure
it with the Velcro and the relative buttons.
HANDLE AND HOOD ADJUSTMENT
fig. 25 To adjust the handle and the hood, press the two
buttons on the sides (C4) simultaneously.
fig. 26 CAUTION: to transport the carrycot, always hold
it by the handle.
ATTACHING THE APRON
fig. 27 Fasten all the apron buttons to the carrycot.
INTERNAL VENTILATION
fig. 28 Internal ventilation can be adjusted by means of
the lever (C5).
BACKREST ADJUSTMENT
fig. 29 Operate the lever (C6) to adjust the backrest: once
the desired position is reached, set the lever to the starting
position.
MATTRESS AND INTERNAL LINING MAINTENANCE
fig. 30 It is advisable to remove the mattress and internal
lining periodically for correct maintenance.
CAB 0+ INFANT CAR SEAT (IF AVAILABLE)
ATTACHING THE INFANT CAR SEAT TO THE CHASSIS
fig. 31 Take the infant car seat from the handle and attach
it to the chassis in correspondence of the housings on
both sides of the structure and place it solely in rear facing
position.
fig. 32 CAUTION: make sure that the infant car seat is
properly attached before use.
DETACHING THE INFANT CAR SEAT FROM THE CHASSIS
fig. 33 Use the lever (S1) on the rear of the infant car seat.
fig. 34 Simultaneously, lift the seat by holding it by the
handle.
To use the Cab 0+ infant car seat properly, refer to the
dedicated manual.
QUAD PUSHCHAIR SEAT
ATTACHING THE PUSHCHAIR SEAT TO THE CHASSIS
fig. 35 Attach the pushchair seat to the chassis, in
correspondence of the housings on both sides of the
structure.
fig. 36 CAUTION: make sure that the pushchair seat is
properly attached before use.
fig. 37 The seat can be used facing the mother or facing
the street.
DETACHING THE PUSHCHAIR SEAT FROM THE CHASSIS
fig. 38 Press the handles (R5) simultaneously and lift the
pushchair seat off the chassis.
CAUTION: do not, under any circumstance, carry out this
operation with the baby inside.
ADJUSTING THE BACKREST
fig. 39 The backrest can be adjusted to 4 positions; use
the central device (R6) and bring the backrest to the desired
position.
ADJUSTING THE FOOTREST
fig. 40 Press both buttons (R7) on the lower part of the
footrest and push it down.
fig. 41 To lift the footrest, simply pull it upwards and it
shall automatically lock into position.
The footrest can also be extended further to follow your
28
child's growth.
fig. 42 To extend it, use the small button (R17) underneath
and pull out the footrest extension at the same time (R16).
fig. 43 To bring it back to its original position, press the
button (R17), while pushing the footrest extension (R16) into
its housing.
SAFETY BELTS
fig. 44 Ensure that the safety belts are inserted in the
eyelets at the height of the shoulders or immediately above.
If the position is not correct, remove the belts from the first
pair of eyelets and reinsert them in the second one; always
use eyelets at the same height.
fig. 45 Make sure that the back strap is properly inserted
in the ends of the waist one.
fig. 46 Fasten the ends of the strap belt to the central
buckle.
fig. 47 The waist strap must always pass through the side
loops (R8) and, when being used, it must be adjusted in order
to properly secure the baby.
fig. 48 Always use the crotch strap together with the waist
one, adjusting both of them properly.
CAUTION! Failure to comply with this precaution can
cause the baby to fall or slide out, with serious injury
risks.
ATTACHING THE HANDRAIL
fig. 49 Mount the handrail (R1) by pressing the buttons
(R9) and attach it in correspondence of the relative housings
on the pushchair seat (R10).
fig. 50 The handrail can be open on one side or fully
removed; to open it, press the button (R9) and remove it from
its housing; to remove it, repeat the procedure on the other
side.
ATTACHING THE HOOD
fig. 51 After inserting the first coupling (H1) into place on
the backrest of the seat (R11), accompany the lining inside
the chassis, taking care to insert the two flaps (H3) into the
rear coupling points (H4).
fig. 52 Complete the assembly of the hood (R2) by
inserting the second coupling (H2) in place.
fig. 53 To adjust the hood, simply accompany it to the
desired position.
DETACHING THE HOOD FROM THE STROLLER
fig. 54 Remove the hood from the stroller by simply
pulling it firmly out of its side coupling points on the backrest
of the seat.
CARING FOR THE HOOD LINING
fig. 55 The lining of the hood can be removed for it to be
cared for properly.
Remove the elastic eyelets (H5) from both couplings and
release the buttons on the hood joints (H6).
fig. 56 Then remove the white front (H7) and rear black
(H8) safety bands from both joints (H6) and remove the
lining completely.
fig. 57 Refit the lining by inserting the white front (H7)
and rear black (H8) safety bands in the relative guides on the
inner lining.
fig. 58 Then insert both safety bands in the relative
coupling points on the joints (H9), making sure the white
safety band (H7) remains at the front and the black one (H8)
at the back.
fig. 59 Complete the assembly by coupling the two
small elastic eyelets (H5) to both hood joints (H1-H2) and
buttoning up the side snap fasteners.
MUFF
fig. 60 Place the muff (R3) making it pass under the
handrail.