Parameter Settings - Baxi ECO COMPACT Manual Para El Usuario

14. PARAMETER SETTINGS

To set the boiler parameters, press
display shows "F01" alternated with the value of the parameter.
Edit parameters
• To scroll the parameters press
• Press buttons to change the single parameter value;
• Press to save changes, the display shows "MEM";
• Press to leave the function without saving, the display shows "ESC".
ALL MODIFIED PARAMETERS SHOULD BE NOTED DOWN IN THE TABLE AT THE END OF THIS MANUAL.
Parameter
F01
Boiler type 010=airtight chamber
F02 Gas used 000=NATURAL GAS - 001=LPG - 002=gas G25.1
Hydraulic system
000 = instantaneous appliance
F03
003 = appliance with external storage boiler
004 = heating only appliance
Setting programmable relays 1
F04 - F05
000=no associated function
Maximum heating setpoint setting (°C)
F06
000=85°C (Burner goes out at 90 °C)
001=45°C (Burner goes out at 50 °C)
F07 DHW inlet priority configuration
F08 CH max. output (0-100%)
F09 DHW max. output
F10 CH and DHW min. heat output
Delay prior to new ignition in CH mode
F11
000=10 seconds - 001...010 = 1...10 minutes
F12 Identification of boiler model
Pump overrun time in heating mode
F13
000=10 seconds - 001...240 = 1...240 minutes
Test of correct DHW probe position 000=Disabled - 001=Always
F14
enabled
F15 Factory setting
Anti-legionellosis function
F16
000 = Disabled - 055...067 = Enabled (setpoint 55...67°C)
F17 Hydraulic pressure switch configuration
F18
Release parameters for SERVICE
Parameter Description of parameters
F19 Factory
F20 Factory
F21 Factory
F22 Factory
F23 Factory
F24 Factory
F25 Factory
F26 Factory
F27
Factory
F28
Factory
F29 Factory
F30 Factory
F31 Factory
F32 Factory
F33 - F34 Factory
F35 Factory
F36 Factory
and together and hold down for at least 6 seconds. When the function is activated, the
;
Description of parameters
and 2 (See SERVICE instructions)
(0-100%)
(0-100%)
Factory settings
14 F - 1.14 F - 18 F
24 F - 1.24 F
setting 001
setting 000
setting 030
setting 110
setting 010
setting 005
setting 000
setting 165
setting 010
setting 070
setting 020
setting 000
setting 180
setting 170
setting 004
setting 015
setting 020
14 F
000
50
(60 LPG) (60 LPG)
100
(60 LPG)
009
Parameter Description of
parameters
F44 Factory
F45 Factory
F46 Factory
F47 Factory
F48 Factory
F49 Factory
F50
Factory
F51
Factory
F52 Factory
F53 Factory
F54 Factory
F55 Factory
F56 Factory
F57 Factory
F58 Factory
37
Factory settings
1.14 F 18 F 24 F
010
000 - 001
004 000 000
000
000
000
50 55
100
(60 LPG)
50
100 100
000
003
009 008 007
003
000
000
000
001
000
Factory settings
14 F - 1.14 F - 18 F
24 F - 1.24 F
setting 000
(this value depends on
setting
valve calibration)
setting 015
setting 000
(this value depends on
setting
valve calibration)
setting 105
setting 100
setting 005
setting 020
setting 100
setting 000
setting 003
setting 025
setting 000
setting 000
7110102.03 (1-06/13)
1.24 F
004
100
100
007