For Hfm-S Synthesizer Rf Module; Trainer Lead; Diagnosis Lead; Other Accessories, Spareparts - Multiplex ROYALevo 7 Manual De Instrucciones

ROYAL evo 7
quiries to establish which RF module you should use,
and which channels are approved for the region in
which you wish to fly your models.
22.4. Scanner for HFM-S Synthesizer RF
module
# 4 5170 35 MHz A- and B-band
# 4 5171 40/41 MHz band
# 4 5173 36 MHz
# 4 5172 72 MHz
Important: which channels can be used?
Regulations concerning the use of radio-controlled
models vary from country to country. Please make en-
quiries to establish which RF module you should use,
and which channels are approved for the region in
which you wish to fly your models.
The scanner allows you to monitor the frequency band,
and guards against channel clashes. The Scanner mod-
ule is simply plugged into the HFM-S Synthesizer RF
module, and is easy to fit at any time.
The scanner can carry out two tasks:
Checking your channel at power-on (Channel-Check)
The channel you select for the Synthesizer is checked
when you switch the transmitter on. If the channel is al-
ready in use, the Synthesizer stays switched off, and the
user is alerted to the situation by an on-screen warning.
If the scanner picks up no signal during this check, the
transmitter switches itself on in the normal way.
Scanning the whole frequency band
The scanner checks all channels of the frequency band
one by one. All the signals it detects are displayed in bar
graph form on the screen; the height of the bar indi-
cates the signal strength.
Detailed instructions for using the Scanner module for
the HFM-S Synthesizer RF module are supplied with the
module itself.

22.5. Trainer lead

# 8 5121
The ROYALevo7 can be used either as Teacher or Pupil
transmitter in a Trainer (buddy-box) system.
Any MULTIPLEX transmitter fitted with a 5-pin DIN
socket (MULTIPLEX multi-function socket) can be used
as a pupil transmitter. (

22.6. Diagnosis lead

# 8 5105
For carrying out adjustments to the model the receiver
can be operated in Diagnosis mode (DSC - Direct Servo
Control) via a cable, without the transmitter radiating an
RF signal, even if "your" channel is already in use. Con-
nect the transmitter (MULTIPLEX multi-function socket)
to the receiver (charge socket on the switch harness
13.4.)
# 8 5039 or # 8 5046) using the Diagnosis lead. Please
note: Diagnosis mode is only possible with MULTIPLEX
receivers which feature a combined Battery / Diagnosis
socket marked "B/D".
22.7.

Other accessories, spareparts

Item
Transmitter case
Standard transmitter aerial, 110 cm
Transmitter tray
SpaceBox ROYALevo Basic transmitter
tray
SpaceBox ROYALevo weather guard (op-
tional)
PROFI transmitter neckstrap
Neckstrap padding for # 8 5646
"Cross-over" transmitter support strap
PC lead ( 23.)
Receiver module for the MULTInaut IV
channel expansion system (
For more information on accessories and replacement
parts please refer to the current main catalogue or our
internet website www.multiplexrc.de.
23.

PC interface

The multi-function socket on the underside of the
ROYALevo transmitter provides a serial interface to a PC
in addition to the functions of charging, Trainer mode
and Diagnosis mode. This interface offers two functions:
access to transmitter data
for data back-up, software update
use with model flying simulators

23.1. Software update / data back-up

The facility to exchange data between transmitter and
PC provides the following possible functions:
Data back-up
storing (backing-up) model memory data on your PC
Software update (loading new software into the
transmitter)
The latter point in particular enables you to exploit en-
tirely new methods of updating the transmitter soft-
ware or installing new screen languages via the inter-
net. The PC software "ROYALevo DataManager" and cur-
rent software updates in various national languages are
already available in the Download area of our internet
website: www.multiplexrc.de.
Important: please check the version of ROYALevo
DataManager you are using.
For the ROYALevo 7 a later version of the ROYALevo-
DataManager is required than is current at the time of
printing of these instructions (V1.06).
The connecting lead (PC lead # 8 5156) is available from
your local model shop.

23.2. Using a flight simulator

The ROYALevo7 can be used directly with many flight
simulators, without further expansion. The manufac-
turers of flight simulators offer special interface cables
for MULTIPLEX transmitters. If you have a query, please
address it to the simulator manufacturer.
Page 72
# 76 3323
# 89 3002
# 8 5305
# 8 5658
# 8 5655
# 8 5646
# 8 5641
# 8 5640
# 8 5156
# 7 5892
24.)