Maintenance - Jacuzzi BUILDER Serie Manual De Instalación Y Operación

Cleaning the Bath
To clean your bath, simply use a mild, nonabrasive liquid deter-
gent solution. You can protect and restore the gloss to a dulled acrylic
surface by applying an acrylic polish or automotive paste wax.
Never use abrasive household cleaners on any Jacuzzi Whirl-
pool Bath product.
Repairs to the Surface
Major scratches and gouges which penetrate the acrylic surface
will require refinishing. Contact your Jacuzzi Whirlpool Bath dealer
for special instructions.
Purging the Whirlpool System
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE PURGED AT
LEAST TWICE A MONTH
To remove accumulations of bath residue from the whirlpool system,
it is recommended that the whirlpool bath be purged at least twice a
month. For best results, however, we recommend that you purge your
whirlpool bath after each use using our exclusive two-part plumbing
system cleaner made specifically for whirlpool baths.
Systems Clean ™ is available through an authorized Jacuzzi Whirl-
pool Bath Distributor or by calling us direct at 1-800-288-4002.
Instructions for use: Immediately after bathing and exiting the
whirlpool bath, leave the bath water in the tub and add hot water, if
necessary, so the water is at least 2" above the highest jet. Turn on
the unit without the aerator. Pour the contents of the Systems Clean
Packet 1 (taking care not to get the material on yourself) into the bath
near the intake for the circulation pump. Repeat same process with
Systems Clean Packet 2. It is important to use Packet 1 before
Packet 2 to avoid a strong odor. Run the bath for 5 to 10 minutes.
Drain completely and rinse any residue.
If you have followed the standard purging instructions above and still
have an excess accumulation of bath residue and desire an alternative
cleaning mechanism, we recommend SUPER SYSTEMS CLEAN
PLUS manufactured by Stearns Packaging to rectify this condition.
This may be obtained by contacting us at l-800-288-4002. It is
recommended that you follow the instructions provided by the manu-
facturer with the product. Repeated use may be necessary. SUPER
SYSTEMS CLEAN PLUS does not replace the necessity to regularly
purge your whirlpool system with Systems Clean as recommended.
(For additional information about water content, contact us for a copy
of the Jacuzzi Water Quality Primer.)
Bath Additives
NOTE: DO NOT USE OIL OR OIL BASED BATH ADDITIVES.
If you want to use any kind of bath additive, use only a small amount
of low-foaming powder or crystal substance; the whirlpool action
intensifies the foaming properties of soaps.
The use of certain bath oils, bubble baths and bath additives may
increase the level of accumulations of bath residue in the whirlpool
system. If excess accumulations persist, you should discontinue use
of these products.
MAINTENANCE INSTRUCTIONS
Suction Cover/Strainer Maintenance
sary. To do this, remove the center screw and detach the square
cover. Clean the cover by backflushing debris from the holes. Re-
place the suction cover immediately after cleaning. When reinstall-
ing, orient the cover/strainer with the small notch at the bottom. The
gasket must be inserted into the groove of the cover/strainer before
reinstalling onto the suction fitting.
CAUTION: Keep hair a minimum of 6 inches away from the suc-
tion fitting at all times when the whirlpool system is operating.
Hair longer than shoulder length should be secured close to the
head, or a bathing cap should be worn. Do not operate the whirl-
pool system with the suction cover removed! It is a safety de-
vice and must always be in place on the suction fitting to mini-
mize the potential hazard of hair and body entrapment.
SUCTION COVER/STRAINER ASSEMBLY
Lamp
dealer for installation on your bath.
fitting, on the underside of the shell, by pulling out the bulb recep-
tacle. Replacement bulbs (12V, 7W) are available from your Jacuzzi
Whirlpool Bath dealer.
LIGHT BULB REPLACEMENT
21
Clean the suction cover/strainer of hair and debris when neces-
COVER STRAINER
SCREW
NOTCH
An optional lamp kit is available from your Jacuzzi Whirlpool Bath
When the bulb burns out, replace it from the back of the lamp
LOCKING NUT
LIGHT BULB
BULB RECEPTACLE
Jacuzzi Whirlpool Bath© K272000AC 12/04
SUCTION
FITTING
GASKET
LIGHT BEZEL
SHELL