Maintenance - Jacuzzi Espree Serie Manual De Instalación Y Operación

Cleaning the Bath
to clean your bath, simply use a mild, nonabrasive
liquid detergent solution. you can protect and restore the
gloss to a dulled acrylic surface by applying Meguiar's
#10 Mirror Glaze, a product specifically designed for
use on acrylic finishes. If Meguiar's is not available, an
acrylic polish of equal quality or automotive paste wax
is acceptable.
Never use abrasive household cleaners on any
Jacuzzi Whirlpool Bath product.
Repairs to the Surface
Minor scratches which do not penetrate the color
finish can be removed by lightly sanding with 600-grit
wet/dry sandpaper. Restore the gloss using Meguiar's
Mirror Glaze or automotive paste wax.
Major scratches and gouges which penetrate the
acrylic surface will require refinishing. Ask your Jacuzzi
Whirlpool Bath dealer for special instructions.
Purging the Whirlpool System
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE
PURGED AT LEAST TWICE A MONTH
to remove accumulations of bath residue from the whirl-
pool system, it is recommended that a whirlpool bath be
purged at least twice a month. For best results, however,
we recommend that you purge your whirlpool bath after
each use using our exclusive two-part plumbing system
cleaner made specifically for whirlpool baths. Systems
Clean ™ is available through an authorized Jacuzzi
Whirlpool Bath Distributor or by calling us direct at 1-
800-288-4002. Instructions for use: Immediately after
bathing and exiting the whirlpool bath, leave the bath
water in the tub and add hot water, if necessary, so the
water is at least 1" to 2" (25 mm to 51 mm) above the
highest jet. Turn on the unit without the aerator. Pour
the contents of the Systems Clean Packet 1 (taking care
not to get the material on yourself) into the bath near the
intake for the circulation pump. Repeat same process
with Systems Clean Packet 2. It is important to use
Packet 1 before Packet 2 to avoid a strong odor.
Run the bath for 5 to 10 minutes. Drain completely and
rinse any residue.
If you have followed the standard purging instructions
above and still have an excess accumulation of bath
residue and desire an alternative cleaning mechanism,
we recommend SUPER SYSTEMS CLEAN PLUS
manufactured by Stearns Packaging to rectify this
condition. this may be obtained by contacting us at
1-800-288-4002. It is recommended that you follow
the instructions provided by the manufacturer with the
product. Repeated use may be necessary. SUPER
SYSTEMS CLEAN PLUS does not replace the necessity
to regularly purge your whirlpool system with Systems
Clean as recommended.
Lamp
an optional lamp kit is available from your Jacuzzi
Whirlpool Bath dealer for installation on your bath.
Copyright © 2007 by Jacuzzi Whirlpool Bath

MAINTENANCE

When the bulb burns out, replace it from the back of
the lamp fitting, on the underside of the shell, by pulling
out the bulb receptacle. Replacement bulbs (12v, 7W)
are available from your Jacuzzi Whirlpool Bath dealer.
Bath Additives
NOTE: DO NOT USE OIL OR OIL BASED BATH AD-
DITIVES.
If you want to use any kind of bath additive, use only
a small amount of low-foaming powder or crystal sub-
stance; the whirlpool action intensifies the foaming
properties of soaps.
the use of certain bath oils, bubble baths and bath ad-
ditives may increase the level of accumulations of bath
residue in the whirlpool system. If excess accumulations
persist, you should discontinue use of these products.
Suction Cover/Strainer Maintenance
Clean the suction cover/strainer of hair and debris
when necessary. to do this, remove the center screw
and detach the square cover. Clean the cover by back-
flushing debris from the holes. Replace the suction
cover immediately after cleaning. When reinstalling,
orient the cover/strainer with the small notch at the
bottom. the gasket must be inserted into the groove
of the cover/strainer before reinstalling onto the suction
fitting.
CAUTION: Keep hair a minimum of 6" (152 mm)
inches away from the suction fitting at all times
when the whirlpool system is operating. Hair longer
than shoulder length should be secured close to
the head, or a bathing cap should be worn. Do not
operate the whirlpool system with the suction cover
removed! It is a safety device and must always be in
place on the suction fitting to minimize the potential
hazard of hair and body entrapment.
Suction
cover-
strainer
assembly
Light bult
replacement
1
Cover strainer
Screw
Notch
Locking nut
Light bulb
Bulb receptacle
U961000K 06/07
Suction
fitting
gasket
Light bezel
Bath shell