Sime MURELLE 25/55 OF ErP Manual De Instrucciones página 85

4.5 MAINTENANCE
To. guarantee. functioning. and. efficiency. of.
the.appliance,.in.respect.of.the.legal.provi-
sions.in.force,.it.must.be.regularly.checked;.
the.frequency.of.the.checks.depends.on.the.
type. of. appliance. and. the. installation. and.
usage.conditions.
In.any.case,.it.should.be.inspected.at.least.
once.a.year.by.a.qualified.technician.
Carry. out. the. cleaning. of. the. generator. in.
the.following.way:
–. Turn.the.main.switch.off.to.stop.electric.
power.reaching.the.boiler.and.close.the.
gas.feed.cock.
–. Remove. the. outer. casing. and. the. gas.
burner. manifold. unit.. To. clean. the. bur-
ner,.blow.in.a.jet.of.air,.so.as.to.remove.
any. dust. particles. that. may. have. accu-
mulated.
–. Clean.the.heat.exchanger,.removing.any.
dust. or. residue. from. combustion.. When.
cleaning.the.heat.exchanger.or.the.bur-
ners,.chemical.products.or.steel.brushes.
MUST.NOT.BE.USED.
. Make. sure. that. the. tops. of. the. burners.
5
with. the. holes. are. free. from. encrusta-
tions.
–. Reassemble.the.items.removed.from.the.
boiler,.making.sure.to.follow.the.correct.
sequence.
1
–. Check.operation.of.the.main.burner.
–. After.assembly.of.all.the.gas.connections,.
these. must. be. tested. for. soundness,.
using. soapy. water. or. appropriate. pro-
2
ducts..DO.NOT.USE.NAKED.FLAMES.
–. Do. not. use. calcium. chloride. to. treat.
the. plastic. component. during. generator.
maintenance..
4.5.1 Chimney sweep function (fig. 22)
To. check. boiler. combustion,. press. the.
installer's.key. .for.a.few.seconds..
The.chimney.sweep.function.will.switch.on.
and.will.continue.for.15.minutes..From.that.
moment,. the. boiler. will. start. working. in.
heating.mode.at.maximum.power,.with.cut.
off.at.80°C.and.re-ignition.at.70°C.
Before activating the chimney sweep fun-
ction make sure that the radiator valves or
eventual zone valves are open.
The. test. can. also. be. carried. out. with. the.
boiler.working.in.D.H.W..mode..
For.this,.after.activating.the.chimney.sweep.
function,. open. one. or. more. hot. water. fau-
cets.. Under. these. conditions,. the. boiler.
5 5
will. function. at. maximum. power. with. the.
D.H.W.. kept. at. between. 60°C. and. 50°C..
During.the.test,.the.hot.water.faucets.must.
remain.open.
3
If. the. key. . and. . are. pressed. during.
the. 15. minutes. of. the. chimney. sweep. fun-
1 1
ction,.the.boiler.will.be.brought.respectively.
to.maximum.and.minimum.power.
5
The chimney sweep function will automa-
2 2
tically switch off after 15 minutes or when
3
. is pressed again.
the key .
4 4
1
3
[TVw]
55
50
4
45
40
35
30
25
20
TVw. Flow.temperature.setpoint
Tag.
x.
A.
B.
4.5.2 Operation floor drying (fig. 23)
3
The. operation. floor. drying. keeps. the. floor.
at. a. pre-established. temperature. profile.
and. it. is. activated. only. for. those. systems.
combined. with. the. mixed. zone. card. code.
8092233.. The. temperature. profiles. can. be.
selected.by.means.of.the.installer.parame-
ter.PAR.43:.
0.=.Not.activated.function
0 1 5 7 1 5
X A
1
A + B
Period.in.days
Start.day
Functional.heating
Floor.curing.heating
Fig..22
10 15 18
B
25
Fig..23
1.=.Curve.setting.A
2.=.Curve.setting.B
3.=.Curve.setting.A.+.B
The. turning. off. of. . the. function. happens.
clicking.on.the.button.OFF.(return.of.PAR.43.
to.the.value.0).or.automatically.at.the.end.of.
the.function..
The. set. of. the. mixed. zone. follows. the.
development. of. the. selected. curve. and.
ES
PT
2
ENG
[Tag
]
85