Programming Remote Controls - Aprimatic T5-SB Instrucciones Para La Instalación, Uso Y Mantenimiento

Equipo de control para la automatización de barreras para el tráfico de vehículos
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

4.1

PrOgrAMMINg rEMOtE CONtrOLS

 Follow the procedure described in par.4.1A or 4.1B, depending on the receiver installed, to program the remote controls
so that they are recognised by the system.
4.1A WItH 4-CHANNEL CONNECtION rECEIvEr
PL-ECO (Fig.5)
 To assign the StArt button (radio channel to operate)
close the relevant jumper JP1 or JP2 or JP3 or JP4 (Fig.4).
When programming is complete the button selected will
command the StArt.
Enabling self-teach
1 Press all the buttons on the first
remote control to be memorised
if the receiver memory is empty;
alternatively, press all the buttons
on a remote control already
memorised.
mode is enabled for 30 seconds.
- Operation confirmed by: the
LED will light up permanently
and then switch off at the end of
programming time.
30"
During the programming time you can
memorise the first remote control and then
any other remote controls.
At the end of 30 seconds the self-
teach mode finishes.
- Operation confirmed by: The LED
switches off.
If you wish to memorise other remote
controls at this point you must enable
the self-teach once again. To do this,
use one of the remote controls already
memorised and repeat steps  and 
above.
IMPORTANT NOTE:
 When you connect up the power supply, the receiver LED (Fig.6) will flash for 7 seconds (10 times) and then switch
OFF. You can only program the remote control recognition when the LED is OFF.
 If you do not perform programming, after a pause of 30 seconds the LED will switch off and the teach procedure is
finished.
 To leave the programming mode, press the RESET on the receiver. All the data saved to memory and confirmed
will be saved. CAUTION. If you press RESET and at the same time press a button of a remote control already in the
memory, this action will delete the remote control from the memory.
 To completely DELETE the PL-ECO memory (Fig.6):
- Switch OFF the power supply to the receiver for at least 30 seconds.
- Power up the receiver and at the same time press and hold down
RESET until the LED switches off (10 seconds). - After a few seconds
the LED will start to flash and then switch off. The remote controls have
now all be deleted from the memory. NEW emote controls can now
be programmed.
 To DELETE a single remote control from the PL-ECO memory:
- With the receiver powered up, press RESET and at the same time any
button on the remote control to be deleted from the memory.
PL-ECO rECEIvEr
ð
The self-teach
- 1 -
Remote control programming
4.1b WItH MEMOry SyStEM rECEIvEr
(UNICO rECEIvEr)
CAUTION If you are using the UNICO Memory System
receiver you must first remove the PL-ECO receiver.
 Insert the UNICO receiver in the connector K3 (Fig.4).
 Perform the remote command teach procedure following
the instructions supplied with the UNICO receiver.
At the end of programming, button 1 will give the StArt
command (Fig.4).
Memorising the first remote control
2 Press any button on the remote
control.
- Operation confirmed by: the LED
switches off and then on again,
fixed.
Memorising other remote controls
3-A Press all the buttons on the remote
control to be memorised.
- Operation confirmed by: the LED
switches off and then on again, fixed.
3-b Press any button on the remote
control.
A
- Operation confirmed by: the LED
switches off and then on again, fixed.
B
Memorise each remote control one
after the other by repeating steps A
and B within the programming time.
PL-ECO
Fig. 5
LED RESET
Fig. 6

Publicidad

Tabla de contenido
loading

Tabla de contenido