Installing The Hood - Sirius S-DD2 Istrucciones De Uso

2/ INSTALLING THE HOOD

1) Before installing the appliance, make sure that none of the parts is damaged in any way. In case of damaged
parts, contact your retailer and do not proceed with installation.
Read all of the following instructions with care before installing the appliance.
- Use an air outlet pipe of the shortest possible length.
- Limit the number of pipe bends.
- Use a material approved by standards and regulations.
- Avoid any sudden changes in pipe section (recommended constant diameter: 10 mm or equal surface area).
Before the installation of the Downdraft, please remove the security piece you can see in the picture (Fig. 1--
-).
The manufacturer will not be answerable for any capacity or noise problems caused by failure to comply with the
above instructions and the warranty will be rendered null and void.
) After completing the installation and connecting the appliance to the mains electricity, lift the downdraft and
remove the door block (Fig. -6-7). Then open the door (Fig. 8 - 9), remove the PVC grease filter shield (Fig.10),
then place the filters as illustrated in Fig. 11
) Make a rectangular opening, 790 x 100 mm in size, in the back of the cook top for the 90 cm model and 90
x 100 mm for the 60 cm model and 1090x100mm for the 10cm model.
For models with motor already fitted, remove the screws and the extraction unit to fit the downdraft in the rel-
evant hole. At this point, insert a seal (silicone) in the bottom section of the frame support (Fig. 18) and place
in the relevant hole (Fig. 19-0), then proceed to insert the downdraft into the unit.
) In the event that the downdraft is to be placed so that it is next to the cook top, it is possible to join the
downdraft hole to that of the cook top and in this case, it is no longer necessary to remove the motor.
) Before making the opening, check that there are no structural or other parts inside the cabinet, where the ap-
pliance is to be placed, which could hinder a proper installation. Check that the dimensions of the Downdraft and
the ones of the cooktop are compatible with the cabinet so that the installation can be carried out properly.
6) Put the Downdraft in the opening, inserting it from above as shown in Fig. 1.
7) The upper edge of the Downdraft must fit perfectly the cooktop.
8) Fix the Downdraft inside the cabinet. According to the dimensions of the cabinet and of the air outlet duct,
use the provided fixing brackets.
Attention: do not make any additional openings on the appliance in order to avoid to damage the internal sliding
and electrical components.
9) In the version of the Downdraft equipped with motor, install the motor group adjusting the air evacuation
direction as required, either downwards or upwards. After installing the motor, connect the air ducts (Fig. 1).
The motor can be fitted either on the front or back side of the downdraft..
10) For versions with outside motor, place the suction unit (outside motor) in a suitable area and fit the exhaust
air flue as illustrated in Fig. 1. Proceed to fit the air outlet ducts between the outside motor and the down draft.
Select an air outlet from the five possibilities (Fig. 1) and fit the connection provided.
11) Put the metallic box containing the electronic components in a place easy to be reached if a technical assist-
ance is needed Fig. 1). Connect the electrical connectors of the box to the Downdraft (Fig. 1).
1) For outside motors, connect the motor unit cable to the relevant connector on the electrical components
box.
1) Power the appliance.
Downdraft calibration
After the downdraft has been installed, the aspiration panel must be calibrated. This operation is necessary to
regulate the power exstraction of the aspiration panel. Connect the product to the power line, making sure that
it is conformed to the supply voltage indicated on the technical data tag. Pushing the ON/1 button (dis.
1B for SDD and 1 for SDD TC) the aspiration panel rises. After it has reached a height of 180mm from the
cooketop, press OFF, to stop the extraction then the Timer (fig. 1) and after  sec. the OFF button.
The downdraft will carry out the calibration of its aspiration panel rising and retracting for some centimeters.
During this phase, the buttons on the pushbutton control panel blink. At the end of the calibration, the aspira-
tion panel get back to the previous position and the button end to blink. Wait until the aspiration panel stops
moving before re-activating the extraction.
UTILISATION
This product is intended to extract fumes, fats, and steam from cooking. It has been designed and made for use
18
GB