Safety Instructions; Basic Information Concerning Safety - Hilti POS 150 Guía Rápida

AC adapter
Current input
Power input
Current output
Output voltage (DC)
Weight
Operating temperature
range
Storage temperature
range
Charger
Type
Supply voltage (DC)
Current output
Output voltage (DC)
Weight
Operating temperature range
Storage temperature range
Battery
Type
Rated voltage
Battery capacity
Battery life
Charging time
Operating temperature
range
Storage temperature
range

4 Safety instructions

4.1 Basic information concerning safety

In addition to the information relevant to safety given
in each of the sections of these operating instructions,
the following points must be strictly observed at all
times.
4.2 Misuse
The tool and its ancillary equipment may present hazards
when used incorrectly by untrained personnel or when
used not as directed.
a) Never use the tool without having received the ap-
propriate instruction on its use or without having
read these operating instructions.
for POA 86
(POS 150/180)
–
100 VA
3 A
19 V
0.32 kg (0.7 lbs)
-20...+40°C
(-68°F...+104°F)
-30...+70°C
(-22°F...+158°F)
for POS 150/180
POA 84, Li-ion; charge
with battery charger POA
86
11.1 V
5,000 mAh
at +25°C: 6 h
< 4h
-20...+45°C
(-68°F...+113°F)
-30...+70°C
(-22°F...+158°F)
for POC 100
0.8...0.4 A
–
4 A
5 V
0.25 kg (0.6 lbs)
-20...+40°C
(-68°F...+104°F)
-30...+70°C
(-22°F...+158°F)
for POS 150/180
POA 86 for POA 84 battery (POA 86 is powered by the
POA 85 AC adapter)
19 V
3 A
10...21 V
0.18 kg (0.4 lbs)
-20...+40°C (-68°F...+104°F)
-30...+70°C (-22°F...+158°F)
for POC 100
POA 80, Li-ion; Charge:
directly in POC 100
3.8 V
5,200 mAh
at +25°C: 10 h
< 3h
-20...+50°C
(-68°F...+122°F)
-30...+70°C
(-22°F...+158°F)
b) Do not render safety devices ineffective and do
not remove information and warning notices.
c) Have the tool repaired only at a Hilti Service Center.
Failure to follow the correct procedures when
opening the tool may cause emission of laser
radiation in excess of class 3R.
d) Modification of the power tool or tampering with its
parts is not permissible.
e) To avoid the risk of injury, use only genuine Hilti
accessories and additional equipment.
Never point the tool or its accessories toward
f)
yourself or other persons.
g) Use only clean, soft cloths for cleaning. If necessary,
they may be moistened with a little alcohol.
for POC 200
1.5 A
–
5.0 A
12 V
0.33 kg (0.7 lbs)
-20...+40°C
(-68°F...+104°F)
-30...+70°C
(-22°F...+158°F)
for POC 200
POA 90, Li-ion; Charge:
directly in POC 200
7.5 V
6,000 mAh
at +25°C: 16 h
< 3h
-30...+60°C
(-22°F...+140°F)
-30...+70°C
(-22°F...+158°F)
19
en