Cleaning And Lubrication; Required Maintenance At Ridgid Independent Service Center; Accessories; Storage - RIDGID RE 6 Manual Del Usuario

RE 6/RE 60 Electrical Tool

Cleaning And Lubrication

1. Wipe exterior of the electrical tool clean daily with a
clean dry cloth.
2. Clean the interior of the QCS coupling first by pointing
the opening towards the ground and gently shaking
any debris out. Then, visually inspect the area for any
debris. If needed, cotton swabs can be used to wipe
out any remaining debris. Do not force any material
into the pockets that hold the retaining balls.
3. The QCS coupling is lubricated for life at the factory
and does not require any further lubrication. Do not
add any lubricant to the QCS coupling.
Required Maintenance At RIDGID
Independent Service Center
After 30,000 cycles, the electrical tool will show a blinking
yellow LED on the LED diagnostic display (Figure 2) as long
as the tool is turned ON to indicate that it is time for main-
tenance and recalibration. If the tool is not serviced within
2,000 cycles after the yellow LED light begins blinking;
the LED light will remain solidly lit and the tool will not run.

Accessories

WARNING
The following tool accessories have been de signed
to function with the RE 6 and RE 60 Electrical Tools.
Other accessories suitable for use with other tools
may become hazardous when used on the RE 6 and
RE 60. To prevent serious injury, use only accessor -
ies specifically designed and recommended for use
with the RE 6 or RE 60, such as those listed below.
Catalog
No. Description
44693 18V 2.0Ah North & Latin America, Australia
44698 18V 4.0Ah North & Latin America, Australia
43458 120V Advanced Lithium Battery Charger
43333 230V Advanced Lithium Battery Charger
52083 RE 6 Carrying Case (Plastic)
52283 4P-6 4PIN™ Dieless Crimp Head
52078 Swiv-L-Punch Knockout Punch Head
47918 SC-60C Cutter Head for Copper/Aluminum Wire
49408 SC-60C Cutter Head for ACSR
47913 SC-60C Cutter Head for Copper/Aluminum Wire (China)
49403 SC-60C Cutter Head for ACSR (China)
47778 SC-60B Cutter Head for Copper/Aluminum Wire (Europe)
47763 PH-60B Punch Head
43323 18V 2.0Ah Europe & China
43328 18V 4.0Ah Europe & China
47188 RE 60 Carrying Case (Plastic)
47193 LS-60B Latching Square Head
47198 LR-60B Latching Round Head
8
For a complete listing of RIDGID attachments avail-
able for this tool, see the Ridge Tool Catalog online
at RIDGID.com or call Ridge Tool Technical Service
Department (800) 519-3456.
All listed batteries will work with any electrical tool. The dif-
ference between batteries from different regions is the
applied label(s).

Storage

Remove battery from tool and store electrical tool and bat-
tery in case. Avoid storing the electrical tool, batteries or
charger in extreme heat or cold. The electrical tool will not
turn ON if the tool or battery temperature is not within the
temperature range of 15°F (-10°C) to 122°F (50°C). So it
may be neces sary to allow the tool to warm or cool to a
temperature within the operating range by placing it in a
conditioned room before use. This will be indicated by a
red glowing LED on the LED diagnostic display.
Store the tool in the carrying case and
WARNING
place in a dry, secured area that is out of reach of children
and people unfamiliar with the RE 6/60 Electric Tool.
The electrical tool is dangerous in the hands of untrained
users.

Service And Repair

WARNING
Improper service or repair can make machine
unsafe to operate.
Service and repair on this RE 6/RE 60 Electrical Tool
must be performed by an independent Crimp Tool Service
Cent er. The tool fasteners have been marked to indicate
if service has been performed by unauthorized individuals.
For any repairs or maintenance, contact the Ridge Tool
Technical Service Department at (800) 519-3456 or
RIDGID.com for nearest independent service outlet.
For information on your nearest RIDGID Independent
Service Center or any service or repair questions:
• Contact your local RIDGID distributor.
• Visit RIDGID.com or RIDGID.eu to find your local
RIDGID contact point.
• Contact Ridge Tool Technical Service Department at
rtctechservices@emerson.com, or in the U.S. and
Canada call (800) 519-3456.