Jacuzzi START! 70 Manual De Instalación, Uso Y Mantenimiento página 13

(det.8-9) Insert the tube on the support (E) and then insert
it in the intermediate support (D). Turn the headless screw
without tightening it.
(det.10) Level the side glass panel.
(det.11-12) Adjust and tighten the two headless screws and
insert the hole plug.
Double
i
I
( 11 det.1-2) Insert the glass panel support at the ends
of the tube (B). Turn, but do not tighten, the headless screw.
(det.3-4) Insert the two connection cylinders in the holes.
Fasten the cylinders to the tube (B) using the screws.
(det.5-6) Insert the tubes (C-D) and tighten the headless
screws.
(det.7-8) Insert the support crystals on the ends of the tubes
(C-D). Turn, but do not tighten, the headless screws.
(det.9) Referring to the corresponding dimensions, place the
support tube and mark the point for drilling a hole in the wall.
(det.10) Drill and insert the plug.
(det.11) Put the support tube back in place and secure it with
the screw with washer.
(det.12) Insert the assembled tube (B-C-D) in the wall sup-
port and on the glass panels. Check the correct position of
the three supports cut into the glass panels.
(det.13-14) Turn, but do not tighten, the headless screw.
(det.15) Level all the glass panels. Also check alignment of
the tube (C) with the lower hole of the glass panel.
(det.16-17) Tighten all of the headless screws. Place the
hole plugs.
Round
i
I
( 12 det.1) Remove the fastening screw from the block
(A). Remove the arm (C).
(det. 2) Fasten the support (A) to the glass panel, referring
to the relative dimension. Check its correct position. Tight-
en the headless screw.
(det. 3) Re-position the arm (C). Re-tighten the screw. (det.4)
Set the block (B) on the wall and mark its resting point.
(det.5) Remove the screw from the block (B).
(det.6) Mark the points for drilling, using as a guide the holes
on the block.
i
I
( 13 det.7-8) Drill the holes and insert the dowels.
(det. 9) Re-position the block (B) and fasten it with the
screws. Insert the corresponding hole plugs.
(det. 10) Re-position the arm (C). Re-tighten the screw on
the block (B). Place the corresponding hole plug.
(det. 11) Check the perpendicularity of the glass panels, and
that the magnets are perfectly closed.
(det. 12-13) If necessary, loosen the screw, turn the middle
tube (C) clockwise or counter-clockwise until the correct bal-
ance is achieved.
(det. 14) When adjustment is complete, tighten the screw.
(det. 15) Apply the corresponding hole plug.
Installation of the multi-purpose knob
i
( 14) Complete installation by screwing the knob into the
hole on the front glass panel.
In the 160x90 Double shower box, there will be two knobs,
while the 100x80 model does not have any.
Installation and positioning
of the multi-function panel
Fastening of the wall bracket
i
I
( 15-16 det.1) Position the bracket on the wall referring
to the dimensions shown in the figure.
Mark the positions of the holes, and check that the bracket
is level.
WARNING! The horizontal measurement is to be made
from the compensator.
(det. 2-3) Drill the holes, insert the dowels and fasten the
bracket.
(det.4) Connect the hoses (A) to the wall connections (fe-
male 1/2" G).
NOTE: on the 60x90 Double shower box, there are t-
wo brackets for fastening to the wall.
For the 100x80 model, the wall fastening bracket is to
be installed on the short side of the shower box.
In the model Round 90, where the opening of the door
can be either to the left or to the right, the bracket
must be placed in front of the largest curved glass
panel (the one with the hole).
Assembly of the panel
It is advisable to perform these operations on the floor or
on a suitable support surface.
i
I
( 17 det.1) Insert the brackets in the seats of the column.
(det.2) Install the frame on the column, making sure to insert
it correctly.
(det.3) Insert the crosspiece on the brackets; lock all in place
with the screws (det.4).
(det.5) Run the water pipes under the fastening bracket.
i
I
( 18 det.1) Connect the rubber hose to the large show-
er head via the swivel fitting and gasket (A).
(det.2) Close the column with the snap-in top.
(det.3) Pass the perforated cylinder through the upper hole
on the top and screw it onto the bracket using the screw.
(det.4) Insert the glass panel.
(det.5) Tighten the headless screw using an Allen wrench.
(det.6) Screw the lower cylinder with built-in screw directly
onto the bracket.
Installation of the multi-function panel
NOTE: for the 160x90 Double model, you must first
assemble the wall support tube, then the multi-func-
i
tion panel( 23 det.1-2-3-4).
i
I
( 19 det.1) To insert the previously installed panel on the
wall bracket, you must tilt it downwards, then run the two wa-
ter hoses inside the profile (D) and fasten the support to the
front glass panel (det.2).
(det.3a-b) Secure the panel to the wall bracket by com-
pletely tightening the screw and then locking it with the nut.
(det.4) Level the glass panel using the two adjustment nuts
on the fastening screw of the panel.
13