Final Steps - Jacuzzi START! 70 Manual De Instalación, Uso Y Mantenimiento

WARNING! When installing the panel, secure the glass
panel on which it will rest.
(det.5) Correctly connect the hot and cold water hoses. Make
sure that there are no leaks.
(det.6) Secure the lower part of the panel to the glass pan-
el using the fastening kit.
In models with curved glass, use the contoured rubber gasket.
(det.7-8) Level the panel, tighten the plastic headless screw,
and insert the hole plug.
Now continue installation, following the instruction
in the chapter concerning the installation of fixed
glass panel B.
NOTE: Start! 160x90 Double will have two shower pan-
els. For installation of the second panel, follow the
same steps as previously illustrated.
Installation of side glass panel fastening tubes
(versions with multi-function panel)
i
I
( 20 det.1) Insert the glass panel support on the end of
the side glass panel support tube.
(det.2) Fasten the glass panel support onto the glass panel.
(det.3) Align the tube with the hole on the crosspiece of the pan-
el. Fasten it to the crosspieces with the screw and washer.
(det.4-5) Now level the glass panel.
(det.6-7) Tighten the two headless screws and insert the
hole plug.
Only for walk-in models
i
I
( 21 det.1) Insert the intermediate glass panel support
on the end of the tube that will be fastened to the crosspiece
of the panel (D).
(det.2) Turn the headless screw without tightening it.
(det.3) Align the tube with the hole on the crosspiece of the
panel.
Set it on the glass panel. Check that the grooved support is cor-
rectly positioned.
(det.4) Fasten it to the crosspieces with the screw and washer.
(det.5) Check the 90° angle.
(det.6-7) Tighten the headless screw on the tube (D).
(det.8) After installing the external glass panel support, in-
sert the second tube on the intermediate support (D).
(det.9) Check that the grooved support is properly positioned
on the glass panel. Tighten the headless screw.
(det.10) Level the side glass panel.
(det.11-12) Adjust and tighten all of the headless screws.
Place the hole plug.
Only for model Round
i
I
( 22 det.1) Insert the support on the end of the tube.
(det. 2) Turn the headless screw without tightening it.
(det. 3) Set it on the glass panel. Check that the support is
correctly positioned.
(det. 4) Align the tube to the hole on the crosspiece and
fasten it using the screw with washer.
(det. 5) Level the glass panel.
(det. 6) Tighten the headless screw on the tube.
(det. 7) Tighten the headless screw. Place the hole plug.
Only for model160x90 Double
i
I
( 23 det.1) Referring to the corresponding dimensions,
place the support tube and mark the point for drilling a hole
in the wall. Drill a hole and insert the plug (det.2).
(det.3) Put the support tube back in place and secure it with
the screw with washer.
(det.4) Insert the tube in the support tube.
(det.5-6) Turn, but do not tighten, the headless screw.
(det.7) Now insert the previously installed panel on the wall
bracket. For positioning and fastening, refer the drawing
i
( 19).
(det.8) Fasten the panel to the tube with the screw and washer.
(det.5-6) Check that the panel and glass panels are level.
Then completely tighten the headless screw of the wall sup-
port.
(det.9) Insert the second panel in the wall bracket, following
the same assembly procedure as described above ( i 19).
(det.10) Insert the middle tube. Fasten it with the screws
and washers.
Check that the front glass panels are level, and fasten the panels.
Now completely tighten all of the headless screws (det.11).
Tighten all of the headless screws and insert the hole plugs.
Assembly of multi-purpose shelf
i
I
( 24 det.1) Screw the plastic hose connection into the
shelf using the nut.
(det.2) Connect the tube of the showerhead that comes out
of the previously assembled panel to the hose connection of
the shelf with a plastic clamp.
(det.3) Fasten the shelf to the lower part of the column us-
ing the self-tapping screws.
(det.4) Complete installation by connecting the hose of the
showerhead to the connection on the shelf.
(det.5) Screw the shower head onto the other end of the hose,
including the filter. Place the showerhead on the support.
(det.6) Check for leaks. Then close the upper part of the
panel with the snap-in covers (6a-6b).
(det.7) Remove the two plastic blocks under the door.

Final steps

Assembly of the gasket
i
I
( 25 det.1) Assemble the two ends on the gasket. Re-
move the film from the double-face tape of the indicated ter-
minal and then place the gasket on the door (det.2). Make
sure that the terminal adheres perfectly to the magnet of the
door.
Assembling the under-door profile
i
I
( 26 det.1) Assemble the two terminals at the ends of
the under-door profile.
(det.2) Then apply a line of silicone to the bottom of the pro-
file, along its entire length, as shown.
(det.3) Place the profile on the tray so that it is in contact with
the profiles of the glass panels, as shown (det.3a-3b).
(det.4) Hold the profile in position with adhesive tape until
the silicone is completely dry.
Before applying silicone, make sure that the glass panels are
fastened to the compensators.
14