RIB K400 Manual Del Usuario página 35

EVENT
DIP 1 ON (HOLD MODE)
OR FAILURE OF A SAFETY DEVICE (ON
STEADY MODE)
DIP 2 ON (FULL STROKE PROGRAMMING)
DIP 2>1 ON (PEDESTRIAN STROKE
PROGRAMMING)
PROGRAMMING SEQUENCE STOPPED DUE
TO INTERVENTION OF A SAFETY DEVICE
EVENT
NO REMOTE CONTROL CODE ENTERED
DIP 1 > 2 - FULL OPENING REMOTE
CONTROL CODE PROGRAMMING
DIP 1 > 3 - PEDESTRIAN OPENING REMOTE
CONTROL CODE PROGRAMMING
FULL OPENING REMOTE CONTROL CODE
PROGRAMMING, OUTCOME OK
PEDESTRIAN OPENING REMOTE CONTROL
CODE PROGRAMMING, OUTCOME OK
REMOTE CONTROL CODE NOT PRESENT IN
MEMORY
MEMORY SATURATED BY REMOTE CONTROL
CODES (1000 CODES SAVED)
FULL OPENING CODE DELETION
PEDESTRIAN OPENING CODE DELETION
EVENT
STOP BUTTON PRESSED
PHOTOCELL INTERVENTION
EDGE INTERVENTION
INTERVENTION OF CURRENT SENSOR
FAILURE OF A SAFETY DEVICE OR SAFETY
DEVICE ENGAGED FOR TOO LONG
RUNNING WITH EMERGENCY BATTERIES
(24 Vdc)
EMERGENCY BATTERIES LOW SIGNAL
ALARM FROM EDGE
CURRENT SENSOR ALARM
FAILED AUTO-TEST ALARM
ENCODER FAILURE ALARM
MEMORY NOT INSERTED ALARM
INCORRECT SELF-DIAGNOSTIC ALARM
FUNCTIONAL BLOCK
TABLE SUMMARISING ALARMS AND VISUAL AND SOUND SIGNALS
SIGNALS DURING PROGRAMMING SEQUENCE
BUZZER STATUS
OFF
OFF
OFF
OFF
BUZZER STATUS
OFF
OFF
OFF
1 TONE
1 TONE
OFF
OFF
2 TONES
2 TONES
WARNING SIGNALS DURING OPERATION
BUZZER STATUS
OFF
1 TONE
2 TONES
3 TONES
OFF
OFF
1 TONE EVERY 5 SECONDS FOR 1 MINUTE
(RESET BY ACTIVATING A CONTROL)
2 TONES EVERY 5 SECONDS FOR 1 MINUTE
(RESET BY ACTIVATING A CONTROL)
3 TONES EVERY 5 SECONDS FOR 1 MINUTE
(RESET BY ACTIVATING A CONTROL)
4 TONES EVERY 5 SECONDS FOR 1 MINUTE
(RESET BY ACTIVATING A CONTROL)
5 TONES EVERY 5 SECONDS FOR 1 MINUTE
(RESET BY ACTIVATING A CONTROL)
3 SECONDS ON - 3 SECONDS OFF
TURNS OFF ONLY WHEN THE MEMORY IS
INSERTED
CONTINUOUS TONE FOR 10 SECONDS WITH
A PAUSE OF 2 SECONDS OFF
TURNS OFF ONLY IF DIP 2 IS SET TO OFF
OFF
FLASHER STATUS
OFF
OFF
OFF
OFF
FLASHER STATUS
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
FLASHER STATUS
OFF
OFF
OFF
OFF
OFF
CURRENTLY ENABLED
OFF
ENABLED FOR 1 MINUTE (FLASHING)
ENABLED FOR 1 MINUTE (FLASHING)
OFF
OFF
OFF
OFF
OFF
35
PROGRAMMING LED DL1 STATUS
FLASHES ON-OFF 250 MS
FLASHES ON-OFF 500 MS
FLASHES ON-OFF 500 MS
ON STEADY
TWO-COLOUR DL10 LED STATUS (FOR REMOTE
CONTROL PROG.)
FLASHES INTERMITTENTLY RED/GREEN
FLASHES RED FOR 10 SECONDS
FLASHES GREEN FOR 10 SECONDS
TURNS GREEN ONCE
TURNS RED ONCE
RED FLASH
RUNS 6 GREEN FLASHES
RUNS 2 RED FLASHES
RUNS 2 GREEN FLASHES
LED STATUS AND SIGNAL OUTPUT
LED DL12 TURNS OFF
LED DL13 TURNS OFF
LED DL14 TURNS OFF
NO LED COMBINED
LED DL1 FLASHES ON-OFF 250 MS
SIGNAL OUTPUT FLASHES ON-OFF TWICE FOR
250 MS FOLLOWED BY A PAUSE OF 2 SECONDS
SIGNAL OUTPUT FLASHES CONTINUOUSLY ON-
OFF FOR 500 MS
NO LED COMBINED
NO LED COMBINED
NO LED COMBINED
LED DL2 OFF
NO LED COMBINED
LED DL1 ON STEADY
TWO-TONE LED DL10 IS ON STEADY (ORANGE).