Loose Parts - HIKOKI C 3610DRJ Instrucciones De Manejo

English
Battery
Model
Voltage 36 V / 18 V (Automatic Switching*)
2.5 Ah / 5.0 Ah
Battery capacity
Available cordless
products**
Available charger
* The tool itself will automatically switch over.
** Please see our general catalogue for details.

LOOSE PARTS

The following items are included with your table saw: (Fig. 2)
A: Table saw assembly ......................................................
B: Mitre gauge (in stored position) .....................................
C: Blade guard assembly (in stored position) ....................
D: Anti-kickback pawls assembly (in stored position) ........
E: Outfeed support assembly ............................................
F: Rip fence assembly (in stored position) .........................
G: Push stick (in stored position) .......................................
H: Blade wrench ................................................................
I: 4mm Hex key ................................................................
J: 2.5mm Hex key .............................................................
OPTIONAL ACCESSORIES (Fig.3)
(SOLD SEPARATELY)
A: Battery <BSL36..18>
B: Charger <UC18YSL3(14.4V - 18V)>
C: Battery Cover (Cord No. 329897)
D: Stand Assembly (Cord No. 376510)
Optional accessories are subject to change without notice.
ASSEMBLY
1. Unpacking your table saw
This product requires assembly.
◌ Carefully lift saw from the carton and place it on a level
work surface.
◌ Inspect the tool carefully to make sure that no breakage
or damage occurred during shipping.
◌ Do not discard the packing material until you have carefully
inspected and satisfactorily operated the tool.
◌ The saw is factory set for accurate cutting. After assembling
it, check for accuracy. If shipping has influenced the
settings, refer to specific procedures explained in this
Operator's Manual.
◌ If any part is missing or damaged, do not attempt
to assemble the table saw, insert the battery pack and
turn the switch ON until the missing or damaged part is
obtained and is installed correctly.
CAUTION
This tool is heavy. To avoid back injury, lift with your legs,
not your back, and get help when needed.
BSL36A18 BSL36B18
4.0 Ah / 8.0 Ah
(Automatic Switching*)
Multi volt series, 18 V product
Sliding charger for lithium ion
batteries
WARNING
Remove the protective polyfoam from between the saw's
housing and the motor.
WARNING
The use of attachments or accessories not listed in this
manual might be hazardous and could cause serious
personal injury.
WARNING
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such alteration
or modification is misuse, and could result in a hazardous
condition leading to possible serious personal injury.
WARNING
Do not insert the battery pack and turn the switch ON until
assembly is complete. Failure to comply could result in
accidental starting and possible serious personal injury.
WARNING
Always make sure the table saw is securely mounted to
stable table or work bench. Failure to heed this warning
1
can result in serious personal injury.
1
1
2. You will need
1
Items not supplied
1
◌ Flat head screwdriver
1
◌ Screwdriver
1
◌ Framing square
2
◌ Triangle square
1
Items supplied
1
◌ Blade wrench (2 pc)
◌ 2.5mm Hex key (1 pc)
◌ 4mm Hex key (1 pc)
WARNING
To avoid injury, do not insert the battery pack and turn the
switch ON until it is completely assembled and adjusted
and you have read and understood the operator's manual.
CAUTION
Many of the illustrations in this manual show only portions
of the table saw. This is intentional so that we can clearly
show points being made in the illustrations. Never operate
the saw without all guards securely in place and in good
operating condition.
3. Mounting holes (Fig. 4)
◌ The table saw must be mounted to a firm supporting,
waist high surface such as a stable table, work bench
or leg stand. Four bolt holes (38) have been provided
in the saw's frame bottom for this purpose. Each of the
four mounting holes should be bolted securely using
machine bolts, lock washers, and hex nuts (not included).
Bolts should be of sufficient length to accommodate
the saw's frame bottom, lock washers, hex nuts, and
the thickness of the work bench. Tighten all four bolts
securely.
◌ Carefully check the work bench after mounting to make
sure that no movement can occur during use. If any
tipping, sliding, or walking is noted, secure the work
bench to the floor before operating.
4. To remove/replace/align the table insert (Fig. 5a-5b)
WARNING
The table insert must be level with the saw table. If the
table insert is too high or too low, the workpiece can catch
on the uneven edges, resulting in binding or kickback,
which could result in serious personal injury.
40