Troubleshooting - HIKOKI C 3610DRJ Instrucciones De Manejo

English
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine batteries.
We cannot guarantee the safety and performance of our

TROUBLESHOOTING

WARNING
To avoid injury from an accidental start, turn the switch OFF and remove the battery from the main body before making
any adjustments.
All electrical or mechanical repairs should be done only by qualified service technicians. Contact HiKOKI Authorized
Service Center.
Consult HiKOKI Authorized Service Center if for any reason the motor will not run.
1. Power tool
PROBLEM
Saw will not start.
Does not make 45° and 90° rip
cuts.
Material pinches blade when
ripping.
Material binds on riving knife.
Saw makes unsatisfactory cuts. ◌ Dull blade.
Material kicked back from
blade.
Blade does not raise or bevel
freely.
Blade does not come up to
speed or reset trips too easily.
Machine vibrates excessively. ◌ The saw is not mounted securely to the
Battery cannot be installed.
PROBLEM CAUSE
◌ The battery is not fully installed.
◌ The battery pack empty.
◌ Too lower or high temperature.
◌ Switch not turned on.
◌ Positive stop not adjusted correctly.
◌ Bevel angle pointer not set accurately.
◌ Rip fence not properly aligned.
◌ Rip fence not aligned with blade.
◌ Warped wood, edge against fence is not
straight.
◌ Riving knife not aligned correctly with
blade.
◌ Blade mounted backwards.
◌ Gum or pitch on blade.
◌ Incorrect blade for work being done.
◌ Gum or pitch on blade causing erratic
feed.
◌ Riving knife not aligned correctly with
blade.
◌ Feeding stock without rip fence.
◌ Riving knife not in place.
◌ Dull blade.
◌ The operator letting go of material before
it is past saw blade.
◌ Mitre gauge lock knob is not tightened.
◌ Sawdust and dirt in elevation/beveling
mechanisms.
◌ Extension cord too light or too long.
◌ Low house voltage.
stand.
◌ Stand is on uneven floor.
◌ Workbench is moving.
◌ Damaged saw blade.
◌ Attempting to install a battery other than
that specified for the tool.
cordless power tool when used with batteries other than
these designated by us, or when the battery is disassembled
and modified (such as disassembly and replacement of
cells or other internal parts).
CORRECTIVE ACTION
◌ Insert the battery into the tool until you
hear a click.
◌ Recharge the battery pack.
◌ Keep ambient operating temperature at
-10°~40°C.
◌ Turn the switch on.
◌ See section "Bevel adjusment".
◌ See section "Adjusting bevel indicator".
◌ See section "Aligning rip fence to blade".
◌ See section "Aligning rip fence to blade".
◌ Select another piece of wood.
◌ Align riving knife with blade.
◌ Replace with the specified blade.
◌ Turn the blade around.
◌ Remove the blade and clean with
turpentine and coarse steel wool.
◌ Change the blade.
◌ Clean table with turpentine and steel
wool.
◌ Align riving knife with blade.
◌ Install and use rip fence.
◌ Install and use riving knife (with guard).
◌ Replace with the specified blade.
◌ Push material all the way past saw blade
before releasing work.
◌ Tighten lock knob.
◌ Brush or blow out loose dust and dirt.
◌ Replace with adequate size cord.
◌ Contact your electric company.
◌ Tighten all mounting hardware.
◌ Reposition on flat, level surface.
◌ Securely the workbench to floor.
◌ Replace blade.
◌ Please install a multi volt type battery.
52