Regarding Lithium-Ion Battery Transportation; Glossary Of Terms - HIKOKI C 3610DRJ Instrucciones De Manejo

specified recharging time has elapsed, immediately stop
further recharging.
8. Do not put or subject the battery to high temperatures or
high pressure such as into a microwave oven, dryer, or
high pressure container.
9. Keep away from fi re immediately when leakage or foul
odor are detected.
10. Do not use in a location where strong static electricity
generates.
11. If there is battery leakage, foul odor, heat generated,
discolored or deformed, or in any way appears abnormal
during use, recharging or storage, immediately remove it
from the equipment or battery charger, and stop use.
12. Do not immerse the battery or allow any fluids to flow
inside. Conductive liquid ingress, such as water, can
cause damage resulting in fire or explosion. Store your
battery in a cool, dry place, away from combustible and
flammable items. Corrosive gas atmospheres must be
avoided.
CAUTION
1. If liquid leaking from the battery gets into your eyes, do
not rub your eyes and wash them well with fresh clean
water such as tap water and contact a doctor immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you find rust, foul odor, overheating, discolor, deformation,
and/or other irregularities when using the battery for the
first time, do not use and return it to your supplier or
vendor.
WARNING
If a conductive foreign matter enters in the terminal of lithium-
ion battery, the battery may be shorted, causing fire. When
storing the lithium ion battery, obey surely the rules of following
contents.
- Do not place conductive debris, nail and wires such as iron
wire and copper wire in the storage case.
- To prevent shorting from occurring, load the battery in the
tool or insert securely the battery cover for storing until the
ventilator is not seen.
REGARDING LITHIUM-ION BATTERY
TRANSPORTATION
When transporting a lithium-ion battery, please observe the
following precautions.
WARNING
Notify the transporting company that a package contains a
lithium-ion battery, inform the company of its power output
and follow the instructions of the transportation company
when arranging transport.
• Lithium-ion batteries that exceed a power output of 100 Wh
are considered to be in the freight classification of Dangerous
Goods and will require special application procedures.
• For transportation abroad, you must comply with international
law and the rules and regulations of the destination country.
• If the BSL36B18 (sold separately) is installed in the power
tool, the power output will exceed 100 Wh and the unit will
be classified as Dangerous Goods for freight classification.
Power Output
Wh
2 to 3 digit number
USB DEVICE CONNECTION
PRECAUTIONS (ONLY WITH
UC18YSL3 CHARGER)
When an unexpected problem occurs, the data in a USB
device connected to this product may be corrupted or lost.
Always make sure to back up any data contained in the USB
device prior to use with this product.
Please be aware that our company accepts absolutely no
responsibility for any data stored in a USB device that
is corrupted or lost, nor for any damage that may occur to a
connected device.
WARNING
• Prior to use, check the connecting USB cable for any defect
or damage.
Using a defective or damaged USB cable can cause smoke
emission or ignition.
• When the product is not being used, cover the USB port with
the rubber cover.
Buildup of dust etc. in the USB port can cause smoke
emission or ignition.
NOTE
• There may be an occasional pause during USB recharging.
• When a USB device is not being charged, remove the USB
device from the charger.
Failure to do so may not only reduce the battery life of
a USB device, but may also result in unexpected accidents.
• It may not be possible to charge some USB devices,
depending on the type of device.

GLOSSARY OF TERMS

The safe use of this product requires an understanding of the
information on the tool and in this operator's manual as well
as a knowledge of the project you are attempting. Before use
of this product, familiarize yourself with all operating features
and safety rules.
Anti-kickback Pawls
Kickback is a hazard in which the workpiece is thrown back
toward the operator. The teeth on the anti-kickback pawls
point away from the workpiece. If the workpiece should be
pulled back toward the operator, the teeth dig into the wood
to help prevent or reduce the possibility of kickback.
Bevel Scale
The easy-to-read scale on the front of the cabinet shows the
exact blade angle.
Blade
For maximum performance, it is recommended that you use
the 40-tooth, 254 mm carbide tipped combination blade.
provided with your saw. The blade is raised and lowered with
the height/bevel adjusting handwheel. Bevel angles are locked
with the bevel lock lever.
37
English