HIKOKI C 3610DRJ Instrucciones De Manejo página 43

11. Mitre gauge installation (Fig. 12a-12b)
The mitre gauge (18) can be installed on each mitre gauge
groove (37) on either side of blade.
◌ Remove the mitre gauge (18) from mitre gauge storage
(27) located on inside of the right side of saw.
◌ Slide the guide rail (63) of the mitre gauge (18) into one
of the guide grooves (37) of the saw table intended for
this purpose.
12. To store the table saw accessories (Fig. 13a-13d)
◌ The table saw has two convenient storage areas (one
on either side of the saw ) specifically designed for the
saw's accessories: rip fence (4), blade guard (23), push
stick (8), blade wrenches (20), anti-kickback pawls (1)
and mitre gauge (18).
◌ When not in use, store accessories securely.
13. Connect to a dust collection system (Fig. 14)
◌ The dust extraction port (29) with (Inner: Ø35 mm, Outer:
ø40 mm) size is located on the back of the table saw.
This port can be connected directly to a dust collection
system by connecting the pick up end of the dust
collection hose to the dust port.
◌ Particles generated by cutting may contain substances
that can cause cancer, allergic reactions, respiratory
diseases, birth defects or other reproductive defects.
Some examples of such substances are, lead (in paint
containing lead), additives used for wood treatment
(chromate, wood preservatives), some wood types
(such as oak or beech dust).
◌ The risk depends on how much the user or nearby
persons are exposed to these substances.
◌ Reduce dust exposure with the following measures:
– Do not direct the escaping particles and the exhaust
air stream at yourself or nearby persons or dust
deposits.
– Ensure ventilation of the workplace and wear
appropriate protective equipment, such as respirators
designed to filter microscopically small particles.
– Collect the generated particles at the source, avoid
deposition in the surrounding area.
– Use the supplied dust collection system and a suitable
extraction unit. This ensures that fewer uncontrolled
particles are released to the work environment.
– Use an extraction unit and/or air purifiers.
– Maintain good ventilation of the workplace.
– Keep clean using a vacuum cleaner. Do not sweep
or blow. This will stir up dust.
– Vacuum or wash your protective clothing. Do not blow,
beat or brush. This will stir up dust.
◌ Observe the relevant guidelines for your material, staff,
application and place of application (e.g. occupational
health and safety regulations, disposal).
14. Removal and installation method of battery (Fig. 15)
How to install the battery
◌ Align the battery (64) with the groove inside the tool and
slip it into place.
Always insert it all the way until it locks in place with a
little click, If not, it may accidentally fall out of the tool,
causing injury to you or someone around you (Fig. 15).
How to remove the battery
◌ Withdraw battery (64) from the tool while pressing the
latch (65) (2 pcs) of the battery (64) (Fig. 15).
15. Charging (Fig. 16)
Battery and battery charger are not included with this
product.
Before using the power tool, charge the battery as follows.
◌ Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the charge indicator lamp will blink in red (At 1- second
intervals).
◌ Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 15 (on page 7).
◌ Charging
When inserting a battery in the charger, the charge
indicator lamp will blink in blue.
When the battery becomes fully recharged, the charge
indicator lamp will light up in green. (See Table 2)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as
shown in Table 2, according to the condition of the
charger or the rechargeable battery.
43
English