DBI SALA NANO-LOK 3101207 Manual De Instrucciones página 12

4.7 AERIAL WORK PLATFORMS: Use of the Nano-Lok SRL on aerial work platforms is permissible, provided the following
criteria are met:
1. Nano-Lok SRLs generally will not restrain workers from falling out of aerial work platforms or elevated working
surfaces. To restrain users from falling out of aerial work platforms, Positioning Lanyards of sufficiently short lengths
should be used.
2. Aerial work platforms must have guardrails or gates at all accessible edges along their perimeter unless anchorages
for the Nano-Lok SRLs are located overhead. The edges on the top rails of all guardrails and gates over which the
user might fall must have a minimum radius of 1/8 in. (0.3 cm).
3. Anchorages of appropriate strength and compatibility must always be used for securing Nano-Lok SRLs (see Section 2).
4. Swing fall hazards may exist, especially when working near corners or out away from anchorage points. Added fall
clearance is needed where the potential for swing fall exists (see Figure 4).
5. All sharp edges which the Nano-Lok SRL's lifeline may contact during a fall must be eliminated or covered over.
All edges the SRL lifeline may contact in a fall must be smooth with an edge radius of 1/8 in. (0.3 cm) or greater.
Potential pinch points between adjacent surfaces where the lifeline may catch during a fall must be eliminated.
4.8 HORIZONTAL SYSTEMS: In applications where the Nano-Lok SRL is used in conjunction with a horizontal system
(i.e. Horizontal Lifeline, Horizontal I-Beams Trolley), the SRL and horizontal system components must be compatible.
Horizontal systems must be designed and installed under the supervision of a qualified engineer. Consult the horizontal
system equipment manufacturer's instructions for details.
5.0 INSPECTION
5.1 i-Safe™ RFID TAG: The Nano-Lok SRL includes an i-Safe™ Radio Frequency Identification (RFID) tag (Figure 14). The
RFID tag can be used in conjunction with the i-Safe handheld reading device to simplify inspection and inventory control
and provide records for your fall protection equipment. If you are a first-time user, contact a Capital Safety Customer
Service representative (see back cover); or if you have already registered, go to isafe.capitalsafety.com. Follow the
instructions provided with your i-Safe handheld reader or software to transfer your data to your database.
5.2 INSPECTION FREQUENCY: The Nano-Lok SRL must be inspected at the intervals defined in "Section 2.5 - Inspection
Frequency". Inspection procedures are described in the "Inspection & Maintenance Log" (Table 1).
5.3 UNSAFE OR DEFECTIVE CONDITIONS: If inspection reveals an unsafe or defective condition, remove the Nano-Lok
SRL from service immediately and discard (see "Section 5.5 - Disposal").
5.4 PRODUCT LIFE: The functional life of Nano-Lok SRLs is determined by work conditions and maintenance. As long as the
SRL passes inspection criteria, it may remain in service.
5.5 DISPOSAL: Dispose of the Nano-Lok SRL if it has been subjected to fall force or inspection reveals an unsafe or defective
condition. Before disposing of the SRL, cut the Load Indicator off of the Web Lanyard or otherwise disable the SRL to
eliminate the possibility of inadvertent reuse.
6.0 MAINTENANCE, SERVICING, AND STORAGE
6.1 CLEANING: Cleaning procedures for the Nano-Lok SRL are as follows:
• Periodically clean the exterior of the SRL using water and a mild soap solution. Position the SRL so excess water can
drain out. Clean labels as required.
• Clean the Web Lifeline with water and mild soap solution. Rinse and thoroughly air dry. Do not force dry with heat.
The lifeline should be dry before allowing it to retract into the housing. An excessive buildup of dirt, paint, etc. may
prevent the lifeline from fully retracting back into the housing causing a potential free fall hazard.
IMPORTANT:
with water and a mild soap solution. Inspect the SRL per Table 1 before returning to service.
6.2 SERVICE: Nano-Lok SRLs are not repairable. If the SRL has been subjected to fall force or inspection reveals an unsafe
or defective condition, remove the SRL from service and discard (see "Section 5.5 - Disposal").
6.3 STORAGE/TRANSPORT: Store and transport Nano-Lok SRLs in a cool, dry, clean environment out of direct sunlight.
Avoid areas where chemical vapors may exist. Thoroughly inspect the SRL after any period of extended storage.
7.0 SPECIFICATIONS
7.1 PERFORMANCE: Your Nano-Lok SRL has been tested and certified to the performance requirements of the standard(s)
identified on the cover of this instruction manual. See "Section 2.0 - Limitations & Requirements" for performance
specifications.
7.2 DIMENSIONS: Table 2 lists Nano-Lok SRL dimensions. Average working range for the Nano-Lok SRL is 6 ft. (1.8 m),
but will vary slightly with length differences in the various End Connector options. Retracted and Extended length values
in Table 2 are approximations based on the total length of the fully retracted/extended SRL and the applicable End
Connectors.
7.3 LABELING: Figure 16 at the back of these instructions illustrates Nano-Lok SRL labels.
7.4 MATERIALS: See Table 2.
If the lifeline contacts acids or other caustic chemicals, remove the SRL from service and wash
12