Maintenance Instructions Moving Parts Lubrication; Clutch Jaws Lubrication; Cables; Clutch Jaw Replacement - RIDGID K-1500A Manual De Instrucciones

Tools for C-11, C-12, C-14 and C-15 Cables 1
Catalog Model
No. No. Description
62840 T-1 Straight Auger
61800 T-2 Heavy-Duty Straight Auger
63105 T-3 Funnel Auger
61790 T-4 Heavy-Duty Funnel Auger
63190 T-5 Straight Retrieving Auger
63195 T-6 Funnel Retrieving Auger
63200 T-7 Hook Auger
63205 T-8 Grease Cutter, 2
63210 T-9 Grease Cutter, 3
62845 T-10 Grease Cutter, 4
59480 T-11 "H" Cutter, 2
59485 T-12 "H" Cutter, 3
61970 T-13 Sawtooth Cutter, 2
61975 T-14 Sawtooth Cutter, 3
61770 T-15A Expanding Cutter, 4" - 6"
61825 T-15B Expanding Cutter, 6" - 8"
61960 T-16 Spiral Bar Cutter, 4"
61850 T-17 Spiral Bar Cutter, 6"
61855 T-18 Spiral Bar Cutter, 8"
59625 T-21 Spiral Sawtooth Cutter, 2
63075 T-22 Spiral Sawtooth Cutter, 3"
63085 T-23 Spiral Sawtooth Cutter, 4"
59765 T-24 4-Blade Cutter, 2
59770 T-25 4-Blade Cutter, 3
59775 T-26 4-Blade Cutter, 4
59780 T-26A 4-Blade Cutter, 5
98030 T-50 Includes 3 Sizes: 3" − 4"− 5"
98035 T-50-1 Sharktooth Cutter, 3"
98040 T-50-2 Sharktooth Cutter, 4"
98045 T-50-3 Sharktooth Cutter, 6"
63110 T-31 Chain Knocker, 3" − 4" Pipe
63115 T-32 Chain Knocker, 6" Pipe
63120 T-33 Chain Knocker, 8" Pipe
63145 T-38 Flue Brush, 1
63150 T-39 Flue Brush, 2"
63155 T-40 Flue Brush, 2
63160 T-41 Flue Brush, 3"
63165 T-42 Flue Brush, 3
63170 T-43 Flue Brush, 4"
63175 T-44 Flue Brush, 4
63240 T-45 Flue Brush, 5"
63180 T-46 Flue Brush, 5
63185 T-47 Flue Brush, 6"
NOTE! See RIDGID Catalog for complete list of tools
and accessories.
278-104-421.10_REV. A
K-1500A/B, & K-1500SP Drain Cleaning Machines
1 / "
4
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
Maintenance Instructions
WARNING
Make sure machine is unplugged from power source
before performing maintenance or making any ad-
justment.
Moving Parts Lubrication
Grease all exposed moving parts such as rocker arms
and main bearing approximately every three months.
Make sure to grease main bearing thru grease fitting in-
side clutch handle slot.

Clutch Jaws Lubrication

Clean and lubricate clutch driver jaws with oil after each
use.

Cables

Cables should be thoroughly flushed with water to pre-
vent damaging effects of sediment and drain cleaning
compounds. Periodically lubricate cables and couplings
with RIDGID Cable Rust Inhibitor.
When not in use, store cables indoors to prevent deteri-
oration by the elements.
Cables should be replaced when they become severely
corroded or worn. A worn cable can be identified when
outside coils of cable become flat.
Clutch Jaws Replacement
1. Remove four screws holding the front guard to the
housing.
2. Remove screws from the nose piece assembly (Figure
12).
Figure 12 – Replacing Clutch Jaws
11