Operating Instructions - RIDGID K-400 Manual De Instrucciones

To Couple Cable
and Tools
Snap Together Insert Pin
Figure 12 – Connecting/Disconnecting Tools
10. Securely install the tool to the end of the
cable. The T-slot coupler allows the cutting
tool to be slid onto the cable coupler.
Make sure that the spring-loaded plunger
in the cable coupler moves freely and re-
tains the tool. If the pin sticks in the re-
tracted position, the cutting tool may fall off
in use. To remove cutting tool, insert the
pin key into the hole in the coupling to de-
press the plunger and slide the coupling
apart (see Figure 12).
11. Position the foot switch for easy accessi-
bility. You must be able to hold and control
the cable, control the foot switch, and
reach the FOR/OFF/REV switch.
12. Confirm that the FOR/OFF/REV switch is
in the OFF position.
13. Run the cord along the clear path. With
dry hands plug the drain cleaner into a
properly grounded outlet. Keep all con-
nections dry and off the ground. If the
power cord is not long enough, use an
extension cord that:
• Is in good condition
• Has a three prong plug like on the Drain
Cleaner.
• Is rated for outdoor use and contains a
W or W-A in the cord designation (i.e.
SOW).
• Has sufficient wire size. For extension
cords up to 50' (15,2 m) long use 16
AWG (1,5 mm
sion cords 50'-100' (15,2 m – 30,5 m)
long use 14 AWG (2,5 mm
When using an extension cord, the GFCI
on the drain cleaner does not protect the
extension cord. If the outlet is not GFCI
protected, it is advisable to use a plug in
type GFCI between the outlet and the
extension cord to reduce the risk of shock
if there is a fault in the extension cord.
999-998-156.09_REV. E
To Uncouple Cable and Tools
Slide Apart
2 ) or heavier. For exten-
2 ) or heavier.
K-400 Drain Cleaning Machine

Operating Instructions

WARNING
Always wear eye protection to protect
your eyes against dirt and other foreign
objects.
Only wear RIDGID drain cleaning gloves
or mitts ("gloves"). Never grasp the rotat-
ing cable with anything else, including a
glove or a rag. They can become wrapped
around the cable, causing hand injuries.
Only wear latex or rubber gloves under
RIDGID drain cleaner gloves. Do not use
damaged drain cleaning gloves.
Always use appropriate personal protec-
tive equipment while handling and using
drain cleaning equipment. Drains may
contain chemicals, bacteria and other
substances that may be toxic, infectious,
cause burns or other issues. Appropriate
personal protective equipment always
includes safety glasses and RIDGID drain
cleaning gloves, and may include equip-
ment such as latex or rubber gloves,
face shields, goggles, protective clothing,
respirators and steel-toed footwear.
Do not allow the cutter to stop turning
while the machine is running. This can
overstress the cable and may cause
twisting, kinking or breaking of the cable.
Twisting, kinking or breaking cable may
cause striking or crushing injuries.
Keep gloved hand on the cable when-
ever the machine is running. This pro-
vides better control of the cable and
helps prevent twisting, kinking and
break ing of the cable. Twisting, kinking
or breaking cable may cause striking or
crushing injuries.
Position machine within two feet (0.6m)
of the drain inlet or properly support ex-
posed cable when the distance exceeds
two feet. Greater distances can cause
control problems leading to twisting,
kinking or breaking of the cable. Twist -
ing, kinking or breaking cable may cause
striking or crushing injuries.
One person must control both the cable
and the foot switch. If the cutter stops ro-
tating, the operator must be able to turn
the machine motor off to prevent twist-
ing, kinking and breaking of the cable.
Twisting, kinking or breaking cable may
cause striking or crushing injuries.
11