Layout - Storage - Eurocave 4000 Serie Modo De Empleo

4/ INSTALLING YOUR WINE CABINET
Precautions (Continued)
• For 1-temperature models only, place the humidity cartridge (located
in your cabinet's "accessories" bag) in the base of the cabinet, under
the grid, in the tray provided (see diagram below). When using for the
first time, immerse the entire cartridge in water for a few minutes to
saturate it then drain it thoroughly.
• Install the stop (which is located in the accessories bag) at the back of
the cabinet (see diagram).
• This allows a space of
7 cm to be maintained
between the wall and the
rear of the cabinet. This
space allows your cabinet's
power consumption to be
optimised.
• Place the 2 caps in the 2
holes at the top of the
cabinet.
• Do not push the caps all
the way in, in order to
allow the rear stop to be
installed.
• Slide the rear stop
between the caps and the
wall of the cabinet, then
push the 2 caps all the way in.
Installation
Place your cabinet in the desired location.
It must:
• be open to the outside and well ventilated (not in an enclosed cupboard,
for example),
• not be too damp (utility room, laundry room, bathroom...),
• have a flat, stable floor,
• be supplied with power (standard outlet, 16 A, earthed with 30 mA*
circuit breaker). (* not applicable to some countries).
• Place your cabinet in the desired location.
• Fit the charcoal filter (located in the "accessories" bag) by inserting it
into the breather hole located on the top left-hand side of the inside
of your cabinet.
24
GB
• Wait 48hrs before plugging in your cabinet
• When using your cabinet for the first time, the charcoal filter alarm will
display. Reset the filter meter
to 365 (see chapter 6, § VII).
Installing two cabinets
side by side
N.B.: If you are placing two cabinets side by side, ensure that you leave a
gap of at least 1 cm between each cabinet.
Replacement of the LEDs on the control panel must
only be carried out by a qualified electrician.
Bottles must be arranged so that they do not come into
contact with the back wall. If this happens, the condensation
created on the wall may trickle onto the shelves and damage
the bottle labels. In addition, contact with the cold wall may create a
frost point, which is harmful to your wine.
5/ LAYOUT – STORAGE
Your EuroCave Professional cabinet was designed to be adaptable. Its storage equipment adapts to your requirements and can be added to over
time.
Loading and layout advice
Each shelf can be used as a storage shelf, sliding shelf or display shelf. The shelves in your cabinet have 12 recesses, allowing your
bottles to be stored safely.
1
2
3
30 dowel pins supplied in the accessories bag.
Installing a shelf in storage version
To install bottles on a storage shelf, proceed as follows:
1. Insert 2 runners in the shelf support strips. For each shelf, position one runner on
the right and one runner on the left (see diagram 1). Ensure that the runners are
correctly fixed in their housing (see diagram 2)
2. Place the shelf in the 2 runners. (see diagram 3)
3. Place a locking dowel in each of the 2 holes located at the front of the shelf, in the
upper section. These pins then fix the shelf with respect to the runner and prevent
any unwanted movement.
4. Start by placing bottles in each recess of the back row with the base of the bottle
towards the back.
5. Continue by placing the bottles in the opposite direction on the front row.
6. Continue stacking the bottles, ensuring that no bottles touch the back wall.
7. A storage shelf can support a maximum of 6 rows of 12 bottles, i.e.72 traditional
Bordeaux bottles (97 kg).
Schéma 1
Diagram 1
Schéma 2
Diagram 2 Diagram 3
1 Runners (x2)
2
Shelf - 12 recesses
3 Dowels (x2)
25
GB