Maintenance; General Information; Cleaning - Stiga ST 4851 AE Uso Y Mantenimiento

Ocultar thumbs Ver también para ST 4851 AE:
Tabla de contenido

Publicidad

11.A) which activates 3 or 4 LED lights 
(fig.11.B) which indicate the following:
LED
Battery power reserve
48 V
4 GREEN 100%
3 GREEN 70%
2 GREEN 45%
1 GREEN 10% - Recharge
needed
None
The battery has less than 10% 
power reserve and needs 
recharging immediately.
If at least one LED does not come on 
after 30 minutes charging, the battery 
is faulty and needs replacing.
Battery charging lasts from 1.5 - 3.5 
hours, depending on the battery 
capacity and its residual charge.
The battery charger (5) is the diagnostic 
type fitted with a LED that provides 
information on the battery and charge 
status, based on the following chart:
LED (5a)
GREEN
Battery charging
(Flashing)
GREEN
Fully charged battery
RED
Battery overheated: remove 
the battery and leave it to cool 
for at least 30 minutes
Off
No battery or battery 
inserted incorrectly
RED (Flashing)
Charge  anomaly  and  possible 
faulty  battery;  in  this  case  remove 
the  battery  and  replace  it  within  2 
hours: if the LED indicates charging 
status, this means that the battery is 
in good condition and the charging
can proceed as normal. Otherwise:
- disconnect  the  battery  charger, 
wait a few minutes, and reconnect 
it to the mains again;
- remove  the  battery  from  the 
charger, wait a few minutes, and 
replace it again.
If,  after  all  these  attempts,  the  LED 
(5b) does not indicate the charge
status  and  continues  to  flash,  this 
means that the battery is faulty and 
needs replacing.
80 V
-
100%
70%
30% - Recharge
needed
Meaning
EN - 10

8. MAINTENANCE

8.1 GENERAL INFORMATION

IMPORTANT The safety regulations to
follow during machine use are described in
par. 2.4. Strictly comply with these instructions
to avoid serious risks or hazards.
All service and all maintenance checks
must be carried out on a stationary machine
with the motor switched off. Before any
maintenance operation, switch off the motor
and remove the key from the compartment.
Wear adequate clothing, gloves
and goggles before carrying
out any maintenance.
• The frequency and types of maintenance 
are summarised in the "Maintenance 
Table". The table will help you maintain 
your machine's safety and performance. 
It summarises the main interventions to 
be made and the frequency applicable 
to each of them. Carry out the relevant 
intervention according to the first deadline.
• The use of non-genuine spare parts and
accessories could adversely affect machine 
operation and safety. The manufacturer shall 
decline all liability in the event of injuries 
or damages caused by such parts.
• Genuine spare parts are supplied by 
authorized assistance workshops and dealers.
IMPORTANT All the maintenance and
adjustment operations not described
herein must be carried out by your dealer
or Authorised Service Centre.

8.2 CLEANING

Carry out cleaning operations with the
machine switched off Do not try to remove
snow from the discharge without firstly:
• Releasing the auger control.
• Removing the ignition key
• Removing the battery
Always clean the machine after use. 
To clean the machine adhere to the 
instructions provided below:
• Stop the motor 
• Remove the battery from its compartment. 
• Cool the snow thrower. 
• Clean the snow thrower internally 
and externally with an adequate 
brush and/or compressed air.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

St 8051 aeSt 515 liSt 615 li

Tabla de contenido