Tyre Pressure; Safety Checks; General Safety Check - Stiga TC-TS-TX-TH 102 Serie Traducción Del Manual Original

Tabla de contenido

Publicidad

6.1.3 Tyre pressure

Having the right tyre pressure is the main 
condition for ensuring that the cutting-means 
assembly is horizontal and mows evenly.
1. Unscrew the valve caps
2. Connect a compressed air line with 
a gauge to the valves (fig. 18)
3. Adjust the pressure according to the values
indicated in the "Technical Data" chart.
6.1.4 Preparing the machine
before starting work
NOTE This machine can be used to
mow lawns in a number of different ways;
before starting work, prepare the machine
based on how the lawn is to be mowed.
a. Preparation for grass cutting and
collection in the grass catcher (for
rear collection models only)
– Couple the grass catcher (fig. 20.A) to 
its supports (fig. 20.B) and centre it with 
respect to the plate, making sure that the 
two reference marks are aligned (fig. 20.B).
– Make sure that the lower pipe 
of the grass catcher opening is
attached to the pawl (fig. 20.C).
– If the coupling is difficult or too loose, 
regulate the retaining spring (see 8.9).
b. Preparation for mowing and rear
grass dumping (models with rear
grasscatcheronly)(iffitted)
– If you decide to work without the grass 
catcher, a rear dumping guard kit (fig. 21; 
chap. 15.5) is available upon request. 
This has to be attached to the rear
plate as indicated in the instructions.
c. Preparation for mowing and
mulching of grass
– If you decide to mow the grass, mulching 
it and leaving it on the grass, a "mulching" 
kit is available upon request  (chap. 
15.1). This has to be attached to the rear 
plate as indicated in the instructions.
In the case of models with
side dumping, make sure that the
lateral dumping support has been
mounted (fig. 20.A) (if fitted).
d. Prepare the machine for cutting
and lateral grass dumping (for
models with side dumping only)
– Always make sure that the internal 
deflector springs (fig. 19.A) function 
correctly, maintaining it in the 
lowered position at all times.
– When cutting tall or wet grass, 
we recommend removing the 
lateral dumping strengthener 
(fig. 20.A) (if fitted).
– To remove the strengthener, undo the 
screws (fig. 20.B) while maintaining 
the side dumping deflector in the 
raised position (fig. 20.C).
In the event of collisions without
the side dumping strengthener
fitted (fig. 20.A), the cutting-means
assembly may be deformed.
Always remember to replace the
side dumping strengthener after use.
6.1.5 Positioning the anti-chipping wheels
The anti-chipping wheels are used to reduce 
the risk of tearing up sections of lawn, which 
can occur when the edge of the cutting-means 
assembly drags over irregular ground.
Position the wheels as indicated (par. 7.4). 

6.2 SAFETY CHECKS

Run the following safety checks and 
check that the results correspond to 
those outlined on the tables.
Always carry out the safety
checks before use.

6.2.1 General safety check

Object
Battery
Rear dumping guard, 
grass catcher
Side dumping guard, 
suction grid
Fuel lines and
connections.
Electrical cables.
Oil lines
Safety devices
EN - 15
Result
No damage to the casing, 
cover or terminals
Good condition. No
damage. Properly 
installed.
Good condition. No
damage. Properly 
installed.
No leaks.
All insulation intact.
No mechanical damage.
No leaks. 
No damage.
Proceed as indicated
in par. 6.2.2

Publicidad

Tabla de contenido
loading

Tabla de contenido