OcCre Spirit of Mississippi Instrucciones De Montaje página 7

PHOTO 58: Paint the capstan (no. 53) matt black. Make four 1 mm diameter holes and fit the bars (no. 55) into place. Glue the
capstan to the deck and fir the parts (no. 54) previously painted. Cut the parts (nos. 56 & 57) and sharpen them to a point as
shown in the photo. Glue them in front of the capstan. See plan no. 1.
PHOTO 59 to 61: Paint the doors (no. 59) pale yellow and the hinges in gold. Fit them to the frames (no. 58) but do not glue
them. Use lengths of the strip (no. 60) glued just to the frame, so that the doors do not fall out. Cut the supports (no. 61) and
bend them so that a crossbar can later be fitted. Glue them into the holes in the doors and fit them in place with the crossbar
(no. 62) glued. Glue the three doors into place.
PHOTO 62 to 64: Put together the assemblies shown using the parts (nos. 63 & 64). Fit the strip (no. 65) into the slots and sand
down the whole assembly to unify the surfaces. Paint it matt black and line it with a piece of the plastic net (no. 66) and, finally,
trim off the excess. Glue the strips (no. 67) to the door frames to serve as lintels.
PHOTO 65 & 66: Line the base of the stage (no. 68) using the strips (no. 69). Glue the strips shown (no. 70) onto the edges.
Check the side view in plan (no. 2). Sand down the strips so that they adopt the shape indicated in the plan and fit the lengths of
strip (no. 71). Sand down again to smooth off the lines.
PHOTO 67 to 69: Glue the base in place as shown and onto it fit two strips (no. 72), plus two columns painted red. Covering the
interior frame of the doors fit the columns (no. 74). Also check with plans (nos. 1 & 2). Varnish the complete assembly using a
colourless satin-finish pore-filler varnish.
PHOTO 70 & 71: Decorate the roulette tables (no. 75) in red and black and glue the decorations (no. 76) onto them. Assemble
the chairs and paint the legs and the backs in khaki green. Onto the tables glue the decorations (no. 79), then glue them into
place following deck "A" plan (no. 1 ).
PHOTO 72 & 73: Decorate the piano using black and white. The chairs, like the ones in the photo (no. 70) and the square
tables, in dark brown. Glue the decorations to the tables (no. 84) and fit these assemblies as shown in deck "A" plan (no. 1).
PHOTO 74: Take the deck (no. 85) and, before lining it with the strips (no. 86 y 87), make sure that the slot in the side is
positioned as shown by the arrow. This slot must be located above the structure beneath and for the sides to slot into. There is
also a slot at the back, for the aft bulwark. These two slots must be covered by the lining. The four holes in the centre, and the
holes at the front must be opened up again.
PHOTO 75 to 77: Line the profile with the strips (nos. 88, 89 & 90). Paint the bottom surface of the deck matt white.
PHOTO 78 to 80: Line the side (no. 91) and add the corresponding windows and the doors (no. 93), having previously painted
them using a medium grey and matt black. Also line the two bulkheads (no. 94) using the corresponding strips. Glue the
assembled unit onto the deck. The two bulkheads (no. 94) must end up with the central slots facing upwards.
PHOTO 81 & 82: Glue partition wall (no. 96) to partition wall (no. 97) and paint the area shown matt black, like the two sides
shown in the photo, then glue them in place between the bulkheads. Cut and glue the reinforcements (no. 98) to the corners
and to the ends of the bulkheads.
PHOTO 83 & 84: Find the printed decoration (no. 99) and cut out and glue sections to the wall, following the order indicated for
each section. You can paint the ends of the partitions dark brown.
PHOTO 85 to 88: Line the side (no. 100) with the strips, without cutting out the side slots. Fit the doors and windows, once
painted. Paint the exterior profiles dark brown and the profiles of the doors the same grey colour. Glue the printed decoration
(no. 7) to the side. Fit the side in position, but do not glue it. Cut and glue a length of the strip (no. 98) only to this removable
side.
PHOTO 89: Locate the bulkhead (no. 102) and line it using the required strips. Make sure that the slot the position of the slot is
as shown in the photo. This slot must be covered by the lining strips. Fit the corresponding window, once decorated.
PHOTO 90: Take the bulkhead (no. 105) and line it using the strips. Make sure that the position of the slot is as shown in the
photo. This slot must also be covered by the lining strips. Fit the corresponding window, once decorated.
PHOTO 91 & 92: In the same way go ahead with the lining of the side (no. 107) with the corresponding strips. Decorate the
door and the windows and glue them in place. Glue the bulkheads (nos. 102 & 105) into place and then glue the part (no. 107)
to these and onto the deck.
PHOTO 93: Find the bulkheads (nos. 109 & 110), paint them matt white and glue them into place as shown in the photo.
PHOTO 94 & 95: Cut out and glue the decorations (no. 111) following the order shown, and then fit one window and one door,
once decorated.
PHOTO 96 & 97: Line the side (no. 112), fit doors and windows into place and glue on the corresponding decorations (no. 111).
PHOTO 98: Attach the necessary reinforcements (no. 114), both to the fixed part of the structure and to the removable side.
PHOTO 99 to 101: Glue lengths of the strip (no. 115) onto the deck and, on top of these the strips (no. 116). Then fit the strips
(no. 117) on both sides of the partition and, onto these, fit the shelves (no. 118). Check plan (no. 2). Varnish this assembly.
PHOTO 102 to 104: Make up a table using lengths of the strips (nos. 119, 120 & 121). Varnish it and glue it to this side of the
partition. Glue the barrels (no. 122) into place, once decorated. Put the tables together and paint them a copper colour. Paint
the cooker matt black, its doors copper and the top grey.
PHOTO 105 to 107: Paint the legs (no. 125) red. Cut out the required lengths of the strips (no. 126) to make up the seats and
backrests and then paint them ochre, before gluing them into place. Decorate and glue the barrels, the same as in the galley.
PHOTO 108 to 110: Make up and decorate the tables, chairs, beds and bedside tables. Paint them all a matching khaki green
and olive green. Paint the beds olive green and pale yellow. Check with plan (no. 2).
PHOTO 111: Apply glue, only to the contact surface of the fixed areas, and fit the deck firmly onto the sides of the casino. All of
the sides that cane be seen in the photo must not be glued, so that they can be opened to show the decorated interiors. You
can apply weight on top of the structure to hold it firmly in place while it dries.
PHOTO 112 & 113: Make up the stairway assembly using the parts (nos. 130, 131 & 132). Paint the whole of the structure matt
white. Cut out the lengths required for the steps (no. 133) and fit them to the required widths.
PHOTO 114 to 115: Cut and glue, as shown in the photo, the fencing posts and rails (nos. 134 & 135). Varnish the parts. Fit the
banisters as shown in the photo and paint them red.
PHOTO 116: Paint the supports (no. 143) dark brown and decorate the barrels (no. 122( before gluing them into place, as
shown in the image.