Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Roof Rack Siderail
Contents:
Description
Side Rail Assembly - Right Hand
Side Rail Assembly - Left Hand
Templates (Left Hand & Right Hand)
9mm Drill Bit
Rivnut Tool assembly
Rivnut
Screw Assembly-Pan head-6 Lobe
Installation Instruction
Tools Required
Tape
1/8" Drill bit
Drill Motor
Template (Provided)
9mm Drill Bit (Provided)
GM Super Lube with PTEF (Part number 12371287)
Center Punch
Hammer
Wrench Set
T 25 Torx Driver
Rivnut Tool (Provided)
Create Mounting Holes and Install Rivnuts
1. Use Figure 1 to aid in assembly. Obtain a side rail track and snap
a front and rear base onto each end of the track. Each side rail
track has "INBOARD" stamped into one side. The bases are
identified on the bottom of the parts. The bases should snap onto
the track easily. If force is needed, it is the incorrect base and
belongs on the opposite end of the track.
FIGURE 1
RH FRT
LH RR
LH FRT
RH RR
Roof Rack Siderail
ALL INFORMATION WITHIN
DATE
ABOVE BORDER TO BE PRINTED
EXACTLY AS SHOWN ON 8.5 x 11
29JA07
In
WHITE 16 POUND NON-BOND
17AU07 R
RECYCLABLE PAPER.
PRINT ON BOTH SIDES, EXCLUD-
ING TEMPLATES.
TO BE UNITIZED IN ACCOR-
DANCE WITH GMSPO SPECIFI-
CATIONS.
Quantity
1
1
2
1
1
8
8
1
RH FRT
LH RR
INBOARD
INBOARD
LH FRT
RH RR
REVISION
2. Use Figure 2 to aid in assembly. Position Left Hand template to
driver side. Arrow on template should point forward to front of
vehicle. Align Tab 1 and 2 to the edges of the roof at top tangent
edge of roof Panel. Slide Tab 3 to the roof edge, as shown if not
set by itself after aligning Tab 1 and 2.
Ensure that all three tab points are aligned to the top tangent at
the edge of the roof.
FIGURE 2
3. Use Figure 3 to aid in assembly. Tape the template down on the
roof as shown at 8 places.
Mark the centerline of the hole location with center punch at 1,2,3
and 4 points on the template.
FIGURE 3
(6) TAPE
PART NO.
REV 17AU07
INSTALLATION INSTRUCTIONS
AUTH
DR
TITLE
PART NO.
19166255
6200 Grand Pointe Dr., Grand Blanc, MI 48439
(4) PLACES
19166255
SHEET
Roof Rack Siderail
1
SHEET
1
6
OF
6
OF

Publicidad

loading

Resumen de contenidos para GM 19166255

  • Página 1 Tape 1/8” Drill bit Drill Motor Template (Provided) 9mm Drill Bit (Provided) GM Super Lube with PTEF (Part number 12371287) Center Punch Hammer Wrench Set T 25 Torx Driver 3. Use Figure 3 to aid in assembly. Tape the template down on the roof as shown at 8 places.
  • Página 2 5. Use Figure 5 to aid in assembly. Apply lubricant to holes and 7MM LOCATING HOLE attach the rivnuts to the roof at the above holes with Rivnut tool assembly. FIGURE 5 PART NO. 19166255 Roof Rack Siderail REV 17AU07 SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN...
  • Página 3 Outils nécessaires Ruban Foret de 3 mm (1/8 po) Perceuse électrique Gabarit (fourni) Foret de 9 mm (fourni) Super Lube de GM avec PTFE (numéro de pièce 12371287) Pointeau Marteau Ensemble de clés Mandrin Torx T25 Outil pour écrous noyés (fourni) 3.
  • Página 4 5. Use Figure 5 to aid in assembly. Apply lubricant to holes and TROU DE attach the rivnuts to the roof at the above holes with Rivnut tool POSITIONNEMENT assembly. DE 7 MM FIGURE 5 PART NO. 19166255 Roof Rack Siderail REV 17AU07 SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN DATE REVISION...
  • Página 5: Cinta Adhesiva

    Cinta adhesiva Broca de 1/8” Barreno Plantilla (incluida) Broca de 9mm (incluida) Super Lube de GM con PTEF (número de parte 12371287) Perforadora Martillo Juego de llaves Destornillador Torx T 25 3. Utilice la Figura 3 como referencia para el ensamble. Pegue...
  • Página 6 AGUJERO DE GUÍA de la remachadora de tuercas de remache. DE 7MM (0.28 PULG) FIGURA 5 PART NO. 19166255 Roof Rack Siderail REV 17AU07 SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN...