Safety Information For Circular Table Saws - Parkside PTKS 2000 G5 Traducción Del Manual De Instrucciones Original

Tabla de contenido

Idiomas disponibles

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b) Do not operate power tools in explosive atmos-

pheres, such as in the presence of flammable

Iiquids, gases or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while oper-

ating a power tool. Distractions can cause you to lose

control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Nev-

er modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded sur-

faces, such as pipes, radiators, ranges and refrig-

erators. There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of elec-

tric shock.

e) When operating a power tool outdoors, use an ex-

tension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is un-

avoidable, use a residual current device protected

supply. Use of an RCD reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A mo-

ment of inattention white operating power tools may result in

serious personal injury.

b) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or battery pack, picking up or carry-

ing the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on in-

vites accidents.

d) Remove any adjusting key or wrench before turn-

ing the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper footing and bal-

ance at all times.This applies especially when

working on slopes. This enables better control of the pow-

er tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jew-

ellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

h) Walk when holding the device in your hand. Do not

run.

Do not touch any of the dangerous moving parts

before you have removed the battery and all mov-

ing parts have come to a complete standstill. There

is a risk of injury.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be con-

trolled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjust -ments, changing accessories,

or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentaIly.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands of un-

trained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool's operation. If damaged, have the power tool re-

paired before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less Iikely to

bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into ac-

count the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified re-

pair person using only identical replacement parts.

This will ensure that the safety of the power tool is main-

tained.