Angle Adjustment; Using The Laser; Adjusting The Laser; Use - Parkside PTKS 2000 G5 Traducción Del Manual De Instrucciones Original

Caution!
- Do not push the stop rail (35) too far in the direction of the
saw blade.
- The distance between the stop rail (35) and saw blade (4)
should be approximately 2 cm.

Angle Adjustment

(Figure 27 and 3)
With the table circular saw it is possible to make bevel cuts to
the left at an angle of 0° to 45° to the stop rail. Before each cut,
make sure that no collision is possible between the stop rail (35),
cross-cutting gauge and the saw blade (4).
- Release the clamping screw (11)
- Turn the handwheel (9) to set the desired angle on the scale
(8).
- Lock the clamping srew (11) in the desired angular position.

Using the Laser

(Figures 29-30)
- The laser (28) enables you to carry out precision cuts with
your circular saw.
- The laser light is produced by a laser diode supplied by two
batteries. The laser light is expanded to form a line and is
emitted through the laser exit aperture. You can then use the
line as an optical marking for the cutting line of the precision
cut. Please note the laser safety information.
- Insert the batteries
- Switch on the laser: turn the laser on/off switch (29) to I.
When the saw blade guard (2) is mounted, the laser on/off
switch (29) is accessible through a recess in the guard (Fig-
ure 29). A red laser beam is now projected out of the laser
exit aperture. If you guide the laser beam along the cutting
line mark while sawing, you will achieve clean cuts.
- Switch the laser off: turn the laser on/off switch (29) to 0. The
laser beam goes off. Please always turn the laser off when it
is not required in order to save the batteries.
- The laser beam may be blocked by dust deposits and chips.
You should therefore remove these particles from the laser exit
aperture after every use (with the device switched off).

Adjusting the Laser

(Figure 30)
If the laser (28) no longer shows the correct cutting line, this can
be readjusted. To do this, open the screws (z). Adjust the laser
so that the laser beam hits the cutting teeth of the saw blade (4).
Tighten the screws (z) again. Retighten the screws (z) alternately
and evenly.

Use

Working Instructions

After each new adjustment, we recommend a trial cut in order to
check the set dimensions. After the saw has been switched on,
wait until the saw blade has reached its maximum speed before
you carry out the cut.
Secure long workpieces against tilting at the end of the cutting
process (e.g. unwinding stand etc.)
Only use saw blades with a rotational speed that is equal to or
higher than the rotational speed indicated on the power tool.
Caution with incision cutting.
Operate the device only with a suction system. Check and clean
the suction channels regularly.
Suitability of the saw blades:
- 24 teeth: soft materials, high chip removal, rough cut image
- 48 teeth: hard materials, lower chip removal, finer cut image

Performing Longitudinal Cuts

(Figure 31)
Here, a workpiece is cut in its longitudinal direction. One edge of
the workpiece is pressed against the parallel stop (16) while the
flat side lies on the saw table (1). The saw blade guard (2) must
always be lowered onto the workpiece. The working position dur-
ing longitudinal cutting must never be in a straight line with the
cutting line.
- Adjust the parallel stop (16) according to the workpiece
height and the desired width.
- Switch on the saw.
- Place your hands with the fingers closed together flat on the
workpiece and push the workpiece along the parallel stop
(16) into the saw blade (4).
- Guide from the side with your left or right hand (depending
on the position of the parallel stop) only up to the front edge
of the saw blade guard (2).
- Always push the workpiece through to the end of the riving
knife (3).
- The cutting waste remains on the saw table (1) until the saw
blade (4) is back in its resting position.
- Secure long workpieces against tilting at the end of the cut-
ting process! (e.g. unwinding stand etc.)

Cutting narrow Workpieces

(Figure 32)
Longitudinal cuts of workpieces with a width of less than 120 mm
always have to be cut with the help of a push stick (18). The push
stick is included in the scope of delivery. Replace a worn or dam-
aged push immediately.
• Adjust the parallel stop (16) according to the planned work-
piece width.
• Advance the workpiece with both hands, making sure that
you use a push stick (18) as a pushing aid in the vicinity of
the saw blade.
• Always push the workpiece through to the end of the riving
knife.
Caution! In the case of short workpieces, the
push stick should be used from the beginning of
the cutting process.

Cutting very narrow Workpieces

(Figure 33)
For longitudinal cuts of very narrow workpieces with a width of
30 mm and less, a push block must be used without fail. There is
no push block included in the scope of delivery! (Available from
specialist shops) Replace a worn push block as soon as possible.
• The parallel stop should be adjusted to the cutting width of
the workpiece.
• Press the workpiece with the push block against the stop rail
and push the workpiece with the push stick (18) through to
the end of the riving knife.
GB IE
29