Multiplex Heron KIT Instrucciones De Montaje página 16

Heron KIT
Examine your kit carefully!
MULTIPLEX model kits are subject to constant quality checks throughout the production process, and we sincerely hope
that you are completely satisfied with the contents of your kit. However, we would ask you to check all the parts (referring
to the Parts List) before you start construction, as we cannot exchange components which you have already modified. If
you find a part is not acceptable for any reason, we will gladly correct the defect or replace the item in question once we
have inspected it. Please send the component to our Service Department, with adequate postage pre-paid, being sure to
include the completed complaints form. We are constantly working on improvements to our models, and for this reason
we must reserve the right to change the kit contents in terms of shape or dimensions of parts, technology, materials and
fittings, without prior notification. Please understand that we cannot entertain claims against us if the kit contents do not
agree in every respect with the instructions and the illustrations.
Caution!
Radio-controlled models, and especially model aircraft, are by no means playthings in the usual sense of the
term. Building and operating them safely requires a certain level of technical competence and manual skill, to-
gether with discipline and a responsible attitude at the flying field.
Errors and carelessness in building and flying the model can result in serious personal injury and damage to property.
Since we, as manufacturers, have no control over the construction, maintenance and operation of our products, we are
obliged to take this opportunity to point out these hazards and to emphasise your personal responsibility.
Warning:
Like every aeroplane, this model has static limits. Steep dives and senseless manoeuvres inappropriate to the type may
result in the loss of the aircraft. Please note: we will not replace the model in such cases. It is your responsibility to ap-
proach the airframe's limits gradually. It is designed for the power system recommended in these instructions, but is only
capable of withstanding the flight loads if built exactly as described and if it is in an undamaged state.
Airborne radio control system components / other accessories
Recommended equipment:
MULTIPLEX receiver, min. RX-7-DR light M-LINK
or RX-7-DR light M-LINK
You may also wish to exploit one of our telemetry-capable M-LINK receivers, and equip your model with sensors such as the
Vario / altimeter and current sensors.
* 2 x Nano-S servos (elevator + rudder)
* 4 x Tiny-S servos (2 x aileron + 2x flap)
* 4 x Servo extension leads, 30 cm
* 2 x Servo extension leads, 40 cm
* 2 x Servo extension leads, 60 cm
or * => # 65170 ServoSet Heron with extension leads
Power set with matching flight battery:
„Solius / Heron" power set, Li-BATT powered
with BL-O 3516-0850 brushless motor, MULTIcont BL 40 S-BEC speed controller also
Li-BATT eco 3/2200 flight battery (M6).
=> 12 x 6" folding propeller, propeller hub, spinner and accessories supplied in the kit as standard!
Power set:
„Solius / Heron" power set
with BL-O 3516-0850 brushless motor, MULTIcont BL 40 S-BEC speed controller
=>12 x 6" folding propeller, propeller hub, spinner and accessories supplied in the kit as standard!
Recommended flight battery:
Li-BATT FX 3/1-2200 (M6)
Adhesives:
Zacki ELAPOR ® 20 g
Zacki ELAPOR ® Super liquid, 10 g
Hot-melt adhesive, contact cement for canopy
Battery charger:
HiTEC Multicharger X1 AC Plus, with
power supply AC/DC 100-240V/10-18V 6,0A
Balsa knife, side-cutters, screwdriver (for M3 and M5), 13 mm A/F spanner, hot-melt glue gun.
Tools:
16
GB
Order No. 5 5810
Order No. 5 5818
Order No. 6 5120
Order No. 6 5121
Order No. 8 5031 (for fuselage)
Order No. 8 5029 (for ailerons in wings)
Order No. 8 5032 (for elevator and rudder)
Order No. 33 3660
Order No. 33 2660
Order No. 15 7351
Order No. 59 2727
Order No. 59 2728
Order No. 114 118
# 21 4276