Tabla De Contenido - Brother E Serie Manual De Instrucciones

1. NAMES OF MAJOR PARTS ..................................
2. MACHINE SPECIFICATIONS ................................
3. SEWING PATTERN TABLE ...................................
4. OPTIONAL PARTS .................................................
5. INSTALLATION ...................................................... 11
5-1. Table processing diagram .............................. 12
5-2. Installing the control box ...............................
5-3. Installing the motor ........................................
5-4. Installing the oil pan .......................................
5-5. Installing the machine head ..........................
5-6. Installing the knee lifter plate
(Except-901) ....................................................
5-7. Adjusting the knee lifter (Except-901) ...........
5-8. Installing the belt ............................................
5-9. Installing the bobbin winder .........................
5-10. Installing the belt cover .................................. 21
5-11. Connecting the cords .....................................
5-11-1. Ground wire connections ................. 25
5-11-2. Connecting the harness ...................
5-11-3. Edge trimmer box harness
connection ........................................
5-11-4. Connecting the power cord .............
5-11-5. Connecting the automatic presser
foot lifter harness (ZE-8580
or option) ........................................... 34
5-11-6. Connecting the standing pedal
harness (option) ...............................
5-12. Installing the cotton stand .............................. 36
5-13. Connecting the connecting rod .....................
5-14. Lubrication ......................................................
5-15. Test operation (Operating the treadle) .........
5-15-1. Turning on the power ......................
5-15-2. Operating the treadle .......................
5-16. Adjusting the treadle ......................................
6. PREPARATION BEFORE SEWING ........................ 48
6-1. Installing the needle .......................................
6-2. Removing the bobbin case ............................
6-3. Winding the lower thread ..............................
6-4. Installing the bobbin case ..............................
6-5. Threading the upper thread ..........................
6-6. Adjusting the stitch length ............................
6-7. Backtacking .....................................................
6-8. Adjusting the edge knife height ..................... 58
6-9. Using the thread wiper (ZE-8580-401, -901) .... 60
7. USING THE OPERATION PANEL ......................... 61
7-1. Part names and functions ..............................
7-2. Pattern setting method ..................................
7-2-1. Setting the sewing pattern ..............
7-2-2. Setting the zigzag width ..................
7-2-3. Setting the trimming margin base
line position ......................................
7-2-4. Setting the zigzag stop position .....
7-3. Setting the sewing speed ..............................
7-4. Correction sewing ........................................... 99
7-5. Using slow start (ZE-8580, -8570-A01 only) .... 100
7-6. Setting start backtacking
(ZE-8580, -8570-A01 only) .............................. 101
CONTENTS
1
7-7. Setting end backtacking
(ZE-8580, -8570-A01 only) .............................. 113
3
7-8. Setting fixed stitches/name label sewing
7
(ZE-8580, -8570-A01 only) .............................. 123
9
7-9. Operation panel key locking method ............ 132
8. Using the lower thread counter .......................... 133
9. SEWING ................................................................. 136
13
9-1. Sewing ............................................................ 137
14
9-2. Under edge trimmer sewing ......................... 138
15
10. THREAD TENSION ................................................ 139
16
10-1. Adjusting the thread tension ......................... 139
10-2. Adjusting the presser foot pressure ............. 141
17
11. CLEANING ............................................................. 142
17
19 11-1. Daily cleaning procedures .............................. 143
20 11-2. Applying grease (every three months) ......... 145
12. REPLACING PARTS .............................................. 147
24
12-1. Fixed knife and movable knife
(ZE-8580 only) ................................................. 148
26
12-2. Edge knife ........................................................ 149
12-3. Gauge parts (presser foot, needle plate
30
and feed dog) .................................................. 153
33
12-4. Compression spring ....................................... 156
13. STANDARD ADJUSTMENTS ............................... 157
13-1. Adjusting the thread tension spring ............. 158
13-2. Adjusting the presser foot height ................. 160
13-3. Adjusting the feed dog height ....................... 161
35
13-4. Adjusting the feed dog angle ........................ 162
13-5. Adjusting the forward/back position of
37
the feed dog .................................................... 163
38
13-6. Adjusting the needle and feed
39
mechanism timing ......................................... 164
39
13-7. Adjusting the needle bar height ..................... 165
42
13-8. Needle and rotary hook timing ..................... 166
46
13-9. Hook stopper position .................................... 166
13-10. Adjusting the edge knife cutting pressure .... 170
48
13-11. Adjusting the synchronizer ............................ 171
49
13-12. Adjusting the rotary hook lubrication
50
amount ............................................................ 173
52
13-13. Adjusting the thread trailing length
53
after thread trimming (ZE-8580 only) ........... 175
55
13-14. Adjusting the position of the thread
56
trimming cam (ZE-8580 only) ........................ 179
13-15. Adjusting the tension of the lower thread
presser spring (ZE-8580 only) ....................... 183
13-16. Adjusting the thread wiper (ZE-8580 only) .. 184
61 13-17. Setting the DIP switches ................................ 185
73 13-18. Memory switch setting method ..................... 191
73
14. OPTIONAL PARTS ................................................. 208
81
14-1. Reflection pattern switch ............................... 208
14-2. Dial lock lever ................................................. 209
83
14-3. Thread guide F ................................................ 210
91
15. CHANGING THE BASE LINE FOR PATTERN SIDEWAYS
92
MOVEMENT FROM RIGHT EDGE TO CENTER OF PATTERN ... 211
16. TROUBLESHOOTING ........................................... 219
16-1. Machine head ................................................. 219
16-2. Operation panel ............................................... 222
16-3. List of error codes ........................................... 223