Multiplex Magister Instrucciones De Montaje página 23

Examine your kit carefully!
MULTIPLEX model kits are subject to constant quality checks throughout the production process, and we sincerely hope that you
are completely satisfied with the contents of your kit. However, we would ask you to check all the parts before you start construction,
as we cannot exchange components which you have already worked on. If you find any part is not acceptable for any
reason, we will readily correct or exchange it. Just send the component to our Model Department. Please be sure to include the
purchase receipt and a brief description of the fault.
We are constantly working on improving our models, and for this reason we must reserve the right to change the kit contents in
terms of shape or dimensions of parts, technology, materials and fittings, without prior notification. Please understand that we
cannot entertain claims against us if the kit contents do not agree in every respect with the instructions and the illustrations.
Caution!
Radio-controlled models, and especially model aircraft, are by no means playthings. Building and operating them safely
requires a certain level of technical competence and manual skill, together with discipline and a responsible attitude at
the flying field. Errors and carelessness in building and flying the model can result in serious personal injury and
damage to property. Since we, as manufacturers, have no control over the construction, maintenance and operation of
our products, we are obliged to take this opportunity to point out these hazards and to emphasise your personal
responsibility.
Additional items required:
For the electric and glow powered models:
Receiving system (in the model)
MULTIPLEX Micro IPD receiver
alternatively:
or MULTIPLEX RX-9 Synth DS IPD receiver
MULTIPLEX Mini HD servo, 3 x (4 x for glow version)
Elevator / Rudder / Aileron / Throttle
Additional items for the electric version:
Power set:
MULTIPLEX 680G electric power set
Permax 680/8.4 V, 3:1 gearbox (600 DP), propeller adaptor, spinner and propeller
Speed controller:
MULTIPLEX PiCO-Control 400 Duo
Flight battery:
MULTIPLEX Permabatt NiMH flight pack
Additional items for the glow version:
MULTIPLEX Permabatt NiMH receiver battery 4/1500 mAh
MULTIPLEX switch harness with charge socket, black
Two-stroke motor, approx. 5 cc (.25 - .36 cu. in.)
or
Four-stroke motor, approx. 6.5 cc (.26 - .30), weight no greater than approx. 300 g!
Propeller, spinner, fueltank, electric starter, fuel and glowplugs.
Adhesives: cyano-acrylate ("cyano") and activator; 5-minute epoxy
Use medium-viscosity cyano glue (not styrofoam cyano). It is important to use activator when using cyano. Epoxy adhesives
produce what initially appears to be a sound joint, but the bond is only superficial, and the hard resin breaks away from the parts
under load.
Tools:
Scissors, balsa knife, combination pliers, 2.5 and 4 mm Ø twist drills, cross-point screwdriver, small round file.
Specification:
Wingspan
Fuselage length
All-up weight, electric
All-up weight, glow
Wing area
Wing loading (FAI)
RC functions
Note: please remove the illustration pages from the centre of the instructions.
680 motor / 8 x SC cells
approx. 5 cc motor
Aileron, elevator, rudder and motor; optional aero-tow release
GB
35 MHz A-band
40 MHz band
35 MHz A-band
Speed controller
8/3000 mAh
1630 mm
1170 mm
approx. 2380 g
approx. 1950 g
approx. 45 dm²
approx. 53 g/ dm²
# 21 4193
Order No. 5 5971
Order No. 5 5972
Order No. 5 5890
Order No. 6 5123
Order No. 33 2668
Order No. 7 5024
Order No. 15 6027
Order No. 15 6007
Order No. 8 5039
23