Error Messages - Beninca CP.BN Manual De Instrucciones

If a transmitter code is already stored in the receiver, the radio remote copy can be carried out (without accessing to the control unit).
IMPORTANT: This procedure should be performed with gate leaves open, during the TCA dwell time.
Proceed as follows:
1 Press the hidden key of the already memorised transmitter.
2 Within 5 seconds, press the key of the already memorised transmitter which corresponds to the channel to be matched with the new transmitter
code. The flashing light switches on.
3 Within 10 sec, press the hidden key of the new transmitter.
4 Within 5 sec, press the key of the new transmitter to be matched to the channel selected at point 2. The flashing light switches off.
5 The receiver memorises the new transmitter and exits immediately the programming mode.
The autoset procedure allows for the correct adjustment of the opening/closing torques, at normal speed and during braking, of the gate leaves.
1) Before proceeding with the autoset, check that:
- the movement of the gate leaves is carried out without obstacles present;
- there are no objects/persons standing within the moving area of the automatic system;
- all connections are correct and there is no signal sent by safety devices (PHOT, PHOT C, STOP);
- Move the gate leaves at about half-stroke.
2) Enter the "AUTO" Menu and press the "PRG" push-button . The wording "AUTO" is displayed at 1 sec intervals.
3) By pressing the "PRG" key once more, the self-setting phase starts. This phase consists in the following:
- Short opening operation of both motors (about 5sec)
- Braked closure of both gate leaves until they stop against the mechanic stop in the closing phase.
- Braked opening of both gate leaves until they stop against the mechanical stop in the opening phase.
- Fast closure of both gate leaves until they stop against the mechanic stop in the closing phase.
- Fast opening of both gate leaves until they stop against the mechanical stop in the opening phase.
- Braked closure of both gate leaves until they stop against the mechanic stop in the closing phase.
All these phases should be carried out automatically without any intervention of the operator. The activation of any input (PHOT,PHOT C,
STOP,PP,PED...) immediately annuls the autoset procedure, the gate leaves stop and an "err" message is displayed.
If the procedure is to be stopped, it is sufficient to activate either input or simultaneously press keys + and – on the card.
If the autoset procedure is successfully concluded, the message "ok" will be displayed. Press "PRG" key and exit the autoset menu.
Every autoset procedure, which is successfully concluded, overwrites the procedure previously made.
NOTE: for any modification to the parameters of torque, speed, braking or the start-up order of motors (MINV logics), a new autoset pro-
cedure should be carried out.
An optional accessory is available to power the control unit in the event of power failure.
The BN.CB card must be inserted in the special rapid connector, as indicated in Fig.3.
During normal operation, the green LED is switched on and the card keeps the batteries charged.
In the event of power failure, the card powers the system through the batteries and the red LED switches on.
A F10A fuse protects the control unit during operation with the emergency battery.
If the mains power supply is cut off and batteries are down, both LED's are off.
SWO1 SWC1 SWO2
P.P. PED OPEN
PHOT PHOT-C STOP
The control unit checks the correct operation of the safety devices. In case of malfunctions, the following messages can be displayed:
Error in autoset phase, or storage of remote controls.
ERR
Motor 1 test error.
ERR1
Motor 2 test error.
ERR2
Triggering of thermic protection.
Thrm
REMOTE COPY OF TRANSMITTER CODES
OPERATION OF THE AUTOSET MENU
EMERGENCY BATTERY
In the event of malfunctions, by pressing key + or - the status of all inputs (limit switches, control and
SWC2
safety) can be displayed. One segment of the display is linked to each input. In the event of failure it
CLOSE
switches on according to the following scheme.
N.C. inputs are represented by the vertical segments. N.O. inputs are represented by the horizontal
segments.

ERROR MESSAGES

DIAGNOSTICS
17