UFESA CE7151 Manual De Instrucciones página 19

OUTER ELEMENTS
Wipe the appliance with a damp cloth and dry it. Do not use any brushes or abrasive
cleaning agents as they may scratch outer surfaces.
CLEANING THE STEAM WAND (C)
Keeping the steam wand (C) clean is essential to ensure the maximum performance
of the steam function. Deposits of e.g. dried milk on the wand (C) will decrease its
steaming and frothing capacity.
Important: Wipe the wand (C) clean with a damp cloth and rinse with a little steam
after each use.
Should milk have dried on the steam wand (C), wrap the wand (C) with a clean
damp cloth, place the wand (C) above the drip tray (I) and turn on steam for about
10 seconds. Next, leave the cloth on the wand (C) for about 5 minutes until it soaks.
If there still is dirt on the wand, repeat the procedure.
Important: Never clean the steam wand (C) with an abrasive scourer as it may
damage the wand.
Descaling
Scale is a mineral build-up which naturally occurs on all appliances connected with
heating water. Therefore the espresso machine will require descaling on a regular
basis.
Warning: Descale your coffee maker at least every 3 months. The damages which
are caused by failure to descale the appliance are not subject to warranty repairs.
DESCALING SOLUTIONS
Traditionally, the following agents are used for removal of scale from coffee makers:
● Citric acid solution
Dissolve 2 spoonful (ca. 30 g) of citric acid in 1 l of water.
● Specially designated liquids or tablets
Notice: For liquids and tablets, follow the instructions shown on the packaging of
these products.
DESCALING THE ESPRESSO MACHINE
Warning: Ensure that the espresso machine is switched off and the connecting cord
is disconnected from the socket.
1
Take out the water tank and rinse it clean. Depending on the descaling agent
used, follow the steps below:
A. Espresso machine descaling tablets
Pour about 1l of warm water into the water tank and put in a suitable number of
descaling tablets, as recommended by the manufacturer. When the tablets have
dissolved (it takes about 5-7 minutes), replace the tank.
B. Descaling liquid
Pour about 1.5l of warm water into the water tank. Add a suitable amount of the
descaling agent, as recommended by the manufacturer and replace the tank.
Trouble shooting
PROBLEM POSSIBLE CAUSE
Filter holder (E) is not inserted in the brew head properly or is not
tightened properly.
There are coffee particles around the filter rim (H).
Coffee runs out around
the edge of the filter
Brew head is dirty.
holder
Brew head is damaged.
Rubber seal of the head is damaged or worn out.
No water in the water tank.
Water tank is not properly installed.
Coffee does not run
Knob (K) is set into a different position, e.g.
through
Filter on the brew head may be blocked.
Coffee filter (H) is blocked. Coffee is ground too finely or tamped too
firmly.
2
If the filter holder (E) is in the brew head unit, take it out, rinse thoroughly under
running water and put it aside.
3
Using a screwdriver, unscrew the filter from the bottom of the filter holder unit.
4
Take out the filter, the washer, the screw, and the seal and put them aside in
a safe place.
Important: Be careful not to lose the filter, the washer, the screw or the seal after
disassembling the brew head unit.
5
Using a small delicate brush, clean the brewing area of the head removing all
coffee particles.
6
Place a sufficiently big container under the brew head unit.
7
Insert the plug of the connecting cord in a mains socket and switch on the
espresso machine by pressing button
Warning: Remember that if the standby pilot light (N) flashes, it means that the
espresso machine is in the course of reaching the operating temperature. The
moment the espresso machine has reached the right temperature, the standby pilot
light (N) will stop flashing and will come off. It indicates that the espresso machine
has reached the right temperature and is ready to operate.
8
Turn the regulator knob (K) into the espresso position
decaling solution to flow through the brew head unit.
Important: Do not run the descaling solution through the steam wand (C).
Warning: Depending on the size of the container under the brew head unit, it may
be necessary to empty it during the process.
9
Turn the regulator knob (K) into position 0 to stop the flow (after about half
of the solution has flowed through) and then press button
appliance.
10
Leave the espresso machine for about 10-15 minutes thus allowing the
descaling agent to work.
11
Next, press button
12
Turn the regulator knob (K) into the espresso position
the descaling solution to flow through the brew head unit.
13
Take out the water tank from the appliance and rinse it thoroughly under
running water. Check that all traces of the descaling solution have been removed.
Fill up the tank with fresh water (1) and place it in the espresso machine.
14
Turn on the espresso machine with button
(K) into the espresso position
brew head. Repeat the procedure twice.
Warning: Depending on the size of the container under the brew head unit, it may
be necessary to empty it during the process.
15
When the process has finished, remove the container from under the brew
head and wipe the whole brew head unit thoroughly.
16 Carefully install the rubber seal, the filter, and the washer in the brew head,
following their disassembling procedure in reverse order. Using a screwdriver,
tighten the fastening screw home.
17
Fill the tank up with fresh water (1) and replace it in the espresso machine.
The appliance is ready for further use.
HOW TO FIX, WHAT TO DO
Ensure the holder (E) is properly inserted in the brew head unit and
tightened home. See Brewing espresso.
Clean the rim of the filter (H) and wipe all coffee from the brew head.
Wipe the brew head with a damp cloth.
Contact an authorised service center.
Contact an authorised service center.
Fill up the tank with water (1).
Press the tank down to ensure it sits properly.
Ensure the regulator knob (K) is in position
.
See Descaling.
Empty the filter (H) and rinse it under running water. Wipe the brew
head with a cloth.
(M).
(M). This will turn on the espresso machine.
(M) and turn the regulator knob
. Allow all of the fresh water to flow through the
and allow half of the
(M) and turn off the
and allow the rest of
.