Cutting Height Adjustment; Using The Machine; Preliminary Procedures; Safety Checks - ST CP1 430 Manual De Instrucciones

10a. Electrical protection rating.
Write the identification data of the machine in the specific
space on the label on the back of the cover page.
IMPORTANT Quote the information on the product
identification label whenever you contact an Authorised
Service Centre.
IMPORTANT The example of the Declaration of Con-
formity is provided on the last pages of the manual.
3.4 MAIN COMPONENTS (Fig.1)
A. Chassis.
B. Engine.
C. Cutting means.
D. Rear discharge guard.
E. Grass catcher.
F. Handle.
G. Switch control.
H. Drive operating lever (if available).
DESCRIPTION OF THE SYMBOLS ON THE CONTROLS
(where provided) (Fig.2)
1. WARNING - When the engine starts, the cutting means is
also engaged.
2. Stop
3. Start
4. Drive engaged
5. Grass catcher contents indicator: lifted (a) = empty /
lowered (b) = full
Strictly observe the indications and the safety regu-
lations described in chap. 2.
4. ASSEMBLY
Certain components of the machine are not installed in the
factory and have to be assembled after unpacking, follow-
ing the instructions below.
Unpacking and completing the assembly should be done
on a flat and stable surface, with enough space for moving the
machine and its packaging.. Do not use the machine until
all the instructions provided in the "ASSEMBLY" section
have been carried out.
4.1 UNPACKING (Fig.3)
Remove all the unassembled parts from the box.
1.
2. Take out the machine and dispose of the box and
packaging in compliance with local regulations.
HANDLE ASSEMBLY (Fig.4)
4.2
4.3 GRASS CATCHER ASSEMBLY (Fig.5,6,7)
5. CONTROLS
Double action switch
The engine is controlled by a double action switch, in order to
avoid an accidental start.
To start, press the button and pull the lever (Fig.8.A/B).
When the engine starts, the cutting means is also engaged.
The engine stops automatically when the lever is released.
5.1 DRIVE OPERATING LEVER (Fig.9.A)
IMPORTANT The engine has to be always started
with the drive disengaged.
IMPORTANT Avoid moving the machine backwards
when the drive is ON.
5.2

CUTTING HEIGHT ADJUSTMENT

Do this when the cutting means is stationary.
• Adjustment (See Fig.10.A)
6.

USING THE MACHINE

6.1

PRELIMINARY PROCEDURES

Place the machine in a stable horizontal position on the
ground.
6.1.1 Preparing the machine before starting work
NOTE This machine can be used to mow lawns in vari-
ous ways;.
a. Preparation for grass cutting and collection in
the grass catcher:
1. Insert the grass catcher (Fig.11.A).
b. Preparation for grass cutting and rear grass
discharge on the ground:
1. Lift the rear discharge guard (Fig.12.A) and fit the pin
(Fig.12.B).
c. Preparation for grass mowing and chopping
(mulching function):
Lift the rear discharge guard (Fig.13.A) and fit the chu-
te cap (Fig.13.B) in the discharge opening, keeping it
slightly tilted to the right. Fasten it by fitting the two pins
(Fig.13.B.1) into the holes provided until clicks into place.
6.2

SAFETY CHECKS

Always carry out the safety checks before use.
6.2.1 Safety check before every use
• Check the integrity and the correct mounting
of all components of the machine;
• Make sure that all fastening devices are correctly tightened;
• Keep all surfaces of the machine clean and dry.
6.2.2 Machine operating test
Action
1. Start the machine
(par. 6.3).
2. Release the switch
control levers.
EN - 4
Result
1. The cutting means
should move.
2. The engine must turn
off and the cutting
means must stop with-
in a few seconds.