Stanley SBG700 Traducción De Las Instrucciones Originales página 37

To turn the tool off from a locked-on position, squeeze and
release the paddle switch once.
Spindle Lock
The spindle lock 4 is provided to prevent the spindle from ro-
tating when installing or removing wheels. Operate the spindle
lock only when the tool is turned off, the battery is removed
and has come to a complete stop.
Warning! To reduce the risk of damage to the tool, do not
engage the spindle lock while the tool is operating. Damage
to the tool will result and attached accessory may spin off
possibly resulting in injury.
To engage the lock, depress the spindle lock button and rotate
the spindle until you are unable to rotate the spindle further.
Switching on and off
To switch on, push the lock off lever (1a) backward then
u
press and hold the paddle switch (2).
To switch off, release the paddle switch (2).
u
Warning! Do not switch the tool on or off while under load.
Warning! Always push the lock off lever (1a) forwards to the
locked position when the tool is not in use.
Hints for optimum use
Firmly hold the tool with one hand around the side handle
u
and the other hand around the main handle.
Surface grinding with grinding wheels
Allow the tool to reach full speed before touching the tool
u
to the work surface.
Apply minimum pressure to the work surface, allowing the
u
tool to operate at high speed. Grinding rate is greatest
when the tool operates at high speed.
Maintain a 20˚ to 30˚ angle between the tool and work
u
surface.
Continuously move the tool in a forward and back motion
u
to avoid creating gouges in the work surface.
Remove the tool from work surface before turning tool off.
u
Allow the tool to stop rotating before laying it down.
Edge grinding with grinding wheels
Wheels used for cutting and edge grinding may break or
kick back if they bend or twist while the tool is being used
to do cut-off work or deep grinding. To reduce the risk of
serious injury, limit the use of these wheels with a standard
Type 27 guard to shallow cutting and notching (less than 1/2
inch (13mm) in depth). The open side of the guard must be
positioned away from the operator. For deeper cutting with a
Type 1 cut-off wheel, use a closed Type 1 guard.
Allow the tool to reach full speed before touching the tool
u
to the work surface.
Apply minimum pressure to the work surface, allowing the
u
tool to operate at high speed. Grinding rate is greatest
(Original instructions)
when the tool operates at high speed.
Position yourself so that the open-underside of the wheel
u
is facing away from you.
Once a cut is begun and a notch is established in the
u
workpiece, do not change the angle of the cut.
Changing the angle will cause the wheel to bend and may
cause wheel breakage. Edge grinding wheels are not
designed to withstand side pressures caused by bending.
Remove the tool from the work surface before turning the tool
off. Allow the tool to stop rotating before laying it down.
Do not use edge grinding/cutting wheels for surface grinding
applications because these wheels are not designed for side
pressures encountered with surface grinding. Wheel breakage
and injury may result.
Using wire cup brushes and wire wheels
Wire wheels and brushes can be used for removing rust, scale
and paint, and for smoothing irregular surfaces.
Note: The same precautions should be taken when wire
brushng paint.
Allow the tool to reach full speed before touching the tool
u
to the work surface.
Apply minimum pressure to work surface, allowing the tool
u
to operate at high speed. Material removal rate is greatest
when the tool operates at high speed.
Maintain a 5˚ to 10˚ angle between the tool and work
u
surface for wire cup brushes.
Maintain contact between the edge of the wheel and the
u
work surface with wire wheels.
Continuously move the tool in a forward and back motion
u
to avoid creating gouges in the work surface. Allowing the
tool to rest on the work surface without moving, or moving
the tool in a circular motion causes burning and swirling
marks on the work surface.
Remove the tool from the work surface before turning
u
the tool off. Allow the tool to stop rotating before setting it
down.
Use extra care when working over an edge, as a sudden
sharp movement of grinder may be experienced.
Precautions to take when wire brushing paint
Wire brushing of lead based paint is NOT RECOMMEND-
u
ED due to the difficulty of controlling the contaminated
dust. The greatest danger of lead poisoning is to children
and pregnant women.
Since it is difficult to identify whether or not a paint con-
u
tains lead without a chemical analysis, we recommend the
following precautions when wire brushing any paint:
Personal safety
No children or pregnant women should enter the work
u
area where the paint brushing is being done until all clean
ENGLISH
37