Kärcher SE 2 Car Manual De Instrucciones página 14

ATTENTION
Pointer to a possibly dangerous
situation, which can lead to
property damage.
Description of the Appliance
Illustrations on fold-out page!
When unpacking the product, make sure
that no accessories are missing and that
none of the package contents have been damaged. If
you detect any transport damages please contact your
dealer.
Illustration
1 Container
2 Connection spray hose
3 Filter flap release button
4 Connection for suction hose of the wash vacuum
cleaner
5 Filter dedusting
6 Appliance head
7 Carrying handle
8 Button for vacuuming
9 Spray button
10 Holder for spray suction pipes
11 Container release
12 Flat fold filter *
13 Dirt water reservoir, detachable *
14 Fresh water reservoir, detachable *
15 Spray/suction hose
16 Handle
17 Surrounding air separator
18 Spray lever
19 Lock key for spray mist
20 Lock lever
21 Carpet cleaner RM 519 (100 ml)
Additional vacuuming accessories
22 Attachment for wet/dry vacuuming
23 Crevice nozzle
24 Upholstery nozzle
25 Spray ex hand nozzle for upholstery cleaning
* already installed in the appliance
Before Startup
Illustration
 Turn both releases in the direction of the arrow, re-
move the appliance head and take accessories out
of the container.
Illustration
 Mount wheels and steering rollers.
Illustration
 Attach the accessories holder.
 Wet cleaning
(see chapter "Fill wet cleaning/fresh water reser-
voir")
 Dry vacuum cleaning
(see chapter "Dry vacuuming")
 Vacuuming up moist dirt/water
(see chapter "Vacuuming up moist dirt/water")
Illustration
 Insert and lock the appliance head.
14
Operation
Start up
Illustration
 Attach the suction hose and the spray hose to the
connectors on the appliance.
Note:
Press the suction hose tightly into the connection
so that it locks into place.
Illustration
 Attach the spray ex hand nozzle to the handle and
secure with the locking lever.
 Center the locking lever when attaching it, turn
clockwise to lock.
The appliance is now prepared for wet cleaning.
Wet cleaning of upholstery and carpets
ATTENTION
Check the object to be cleaned prior to using the appli-
ance in an inconspicuous place for colour fastness and
water resistance.
Do not clean water-sensitive floor coverings such as
wood floors (the moisture could penetrate and damage
the floor).
Note
Warm water (max. 50°C) will increase the cleaning ef-
fect.
Only use detergent pump while operating. Avoid dry
runs as well as unnecessary pressure buildup (dynamic
pressure) as much as possible.
If there is a risk of overheating, the thermal protection
switch shuts off the detergent pump. After cooling down
(20 - 30 min), the pump is ready for use again.
Fill the fresh water reservoir
Illustration
You can remove the water reservoir to fill it.
Add 100 - 200 ml of the carpet cleaner RM 519 (volume
depends on degree of soiling) into the fresh water tank,
top up with tap water, do not overfill (observe MAX
marking).
 Use the spray ex hand nozzle to clean upholstery
or carpet.
Start working
Illustration
 Insert the mains plug into the socket.
 Press the switch for vacuuming, suction turbine is
running.
Illustration
 Close fully the surrounding air separator at the han-
dle.
Illustration
 Press the switch for spraying, the detergent pump
is ready.
Illustration
 Use the lever on the spray handle to spray on de-
tergent solution.
Illustration
 For continuous spray, the spray lever can be
locked; for this, activate the spray lever and pull the
locking key toward the rear.
 Run across the surface to be cleaned in overlap-
ping paths. Pull the nozzle backwards (do not
push).
– 8
EN