Bosch 4100 Instrucciones De Funcionamiento página 3

2610048783.qxp_4100 11/17/17 9:10 AM Page 3
▼ Using The Rip Fence Pointer
When Table Is Not Extended . . . . . . . .34
▼ Using The Table Pointer
When Table Is Extended . . . . . . . . . . . .34
▼ Making Rip Cuts Beyond 25
Inches Without The Use Of Scale . . . . .34
▶ Using The Miter Gauge . . . . . . . . . . . . . .35
▼ Adjusting The Miter Angle:
▼ Crosscutting . . . . . . . . . . . . . . . . . . . . .35
▼ Repetitive Crosscutting . . . . . . . . . . . .36
▼ Making The Repetitive Crosscut . . . . . .36
▼ Miter Cutting . . . . . . . . . . . . . . . . . . . .37
▼ Bevel Crosscutting . . . . . . . . . . . . . . . .37
▼ Compound Miter Cutting . . . . . . . . . . .37
▶ Non-Thru Cutting . . . . . . . . . . . . . . . . . . .38
▼ Rabbeting . . . . . . . . . . . . . . . . . . . . . . .38
READ ALL INSTRUCTIONS. Failure to follow the safety rules listed below and
other basic safety precautions may result in serious personal injury.
Work Area
KEEp CHIlDREN AWAY
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
KEEp WORK AREAS ClEAN
Cluttered areas and benches invite accidents.
MAKE WORKSHOp CHIlD-pROOF
With padlocks, master switches.
AVOID DANGEROUS ENVIRONMENTS
Don't use power tools in damp or wet locations.
Keep work area well lit. Do not expose power tools
to rain. Do not use tool in presence of flammable
liquids or gases.
personal Safety
KNOW YOUR pOWER TOOl
Read and understand the owner's manual and la-
bels affixed to the tool. Learn its application and
limitations as well as the specific potential hazards
peculiar to this tool.
DON'T OVERREACH
Keep proper footing and balance at all times.
Stay alert. Watch what you are doing. Use common
sense. Do not op er ate tool when you are tired. Do
not operate while under medication or while using
alcohol or other drug.
DRESS pROpERlY
Do not wear loose clothing or jewelry. They can be
caught in moving parts. Rubber gloves and non-skid
Table of Contents
. . . . . . . . .35
▶ Special Cutting Techniques . . . . . . . . . . .42
▶ Cutting Metals and Masonry . . . . . . . . . .42
Maintaining Your Table Saw . . . . . . . . . . . . .43
Attachments . . . . . . . . . . . . . . . . . . . . . . . . .44
Troubleshooting . . . . . . . . . . . . . . . . . . . . . .45
Miter gauge template . . . . . . . . . . . . . . . . .142
General Safety Rules
footwear are recom mended when working out-
doors. Wear protective hair covering to contain long
hair.
USE SAFETY GOGGlES
Also face or dust mask if cutting operation is dusty,
and ear plugs during extended periods of opera-
tion.
GUARD AGAINST ElECTRIC SHOCK
Prevent body contact with grounded surfaces. For
example: pipes, radiators, ranges, refrigerator en-
closures.
DISCONNECT TOOl FROM pOWER SOURCE
When not in use, before servicing, when changing
blades, bits, cutters, etc.
KEEp GUARDS IN plACE
In working order, and in proper adjustment and
alignment.
REMOVE ADjUSTING KEYS AND WRENCHES
When not in use, before servicing, when changing
blades, bits, cutters, etc.
AVOID ACCIDENTAl STARTING
Make sure the switch is in the "OFF" position be-
fore plugging in tool.
NEVER STAND ON TOOl OR ITS STAND
Serious injury could occur if the tool is tipped or if
the cutting tool is accidentally contacted. Do not
store materials on or near the tool such that it is
necessary to stand on the tool or its stand to reach
them.
SAVE THESE INSTRUCTIONS
▼ Dado Cutting . . . . . . . . . . . . . . . . . . . .38
▼ Installing a Dado Set . . . . . . . . . . . . . .39
▼ Using Stacked Dado Sets . . . . . . . . . . .39
▼ Returning Saw to Normal Thru-Cutting 40
▼ Adjustable or Wobble Dado Sets . . . . .41
▼ Installing a Molding Head Set . . . . . . .41
▼ Returning Saw to Normal Thru-Cutting 42
▼ General Maintenance . . . . . . . . . . . . . .43
▼ Lubrication . . . . . . . . . . . . . . . . . . . . . .43
3