Publicidad
Idiomas disponibles
Idiomas disponibles
TABLE 1
Accessories ø 80
90° curve MF
45° curve MF
Extension L. 1000 (horizontal)
Extension L. 1000 (vertical)
Outlet terminal
Intake terminal
Manifold
Roof outlet terminal L. 1 390
Condensation collection T
The maximum overall length of the
intake and exhaust ducts depends on
the head losses of the single fittings
installed and must not be greater than
7.6 mm H
O vers. "25 Solar" - 9 mm H
2
vers. "30 Solar".
For head losses in the fittings, refer to Table
1 and example fig. 8/a.
2.9. 1
Separate flue kit (fig. 9)
The separate flue kit code 8089904 is
supplied with an intake diaphragm which
must be used as shown in fig. 9/a, depen-
ding on the maximum load loss permitted
in both flues. To use the air intake in this
2
3
6
N° segments
to remove
none
n° 1
n° 1 e 2
da n° 1 a 3
da n° 1 a 4
da n° 1 a 5
da n° 1 a 6
da n° 1 a 7
da n° 1 a 8
da n° 1 a 9
da n° 1 a 10
without diaphragm
"25 Solar"
Intake
Outlet
0.30
0.40
0.20
0.30
0.20
0.30
0.30
0.20
–
0.30
0. 1 0
–
0.20
–
–
–
–
1.00
Example of allowable installation "25 Solar" calculation in that the sum of the head losses of
the single fittings is less than 7.6 mm H
7 meter horizontal pipe ø 80 x 0.20
O
2
7 meter vertical pipe ø 80 x 0.30
n° 2 90° elbows ø 80 x 0.30
n° 2 90° elbows ø 80 x 0.40
n° 1 terminal ø 80
Total head loss
With this total head loss, remove the segments from n. 1 to n. 7 from diaphragm in the
intake pipe.
type of outlet you must perform the fol-
lowing operations (fig. 10):
1
KEY
1 ø125/95 sponge seal
4
2 Fixing screw
3 Flue outlet flange
4 Inlet air diaphragm
6 Manifold with intakes "30 Solar"
25
K mm
180
H mm
125
Total load loss mm H
2
25 Solar
30 Solar
0 ÷ 0.8
0.8 ÷ 1.6
1.6 ÷ 2.4
0 ÷ 1.0
2.4 ÷ 3. 1
1.0 ÷ 2.0
3. 1 ÷ 3.8
2.0 ÷ 3.0
3.8 ÷ 4.5
3.0 ÷ 4.0
4.5 ÷ 5.2
4.0 ÷ 4.8
5.2 ÷ 5.8
4.8 ÷ 5.6
5.8 ÷ 6.4
5.6 ÷ 6.4
6.4 ÷ 7.0
6.4 ÷ 7.2
-
7.2 ÷ 8.0
7.0 ÷ 7.6
8.0 ÷ 9.0
Load loss (mm H 2 O)
Roof out. Intake
Release
–
0.30
–
0.20
–
0.20
–
0.30
–
–
–
0. 1 0
–
0.30
0,50
–
–
–
O:
2
Intake
1.40
0.60
0. 1 0
2. 1 0
– Remove the base of the air intake, using
a tool to cut it off (a);
30
205
165
O
-
-
"30 Solar"
Outlet
Roof out. Intake
0.45
–
0.35
–
0.35
–
0.25
–
0.35
–
–
–
–
–
–
0.55
1.05
–
Outlet
–
–
2. 1 0
–
–
0.80
0.30
+
3.20 = 5.3 mm H
O
2
Fig. 8/a
K
100
Fig. 9
Fig. 9/a
IT
ES
PT
GB
79
Publicidad
