Teka JZC Serie Manual De Usuario página 31

modes described, it is possible
to swap from one mode to the
other by simply turning the knob
to the position required.
IMPORTANT WARNINGS
FOR THE USER
● U s e o f a g a s c o o k i n g
appliance produces heat and
moisture in the room in which
it is installed. The room must
therefore be well ventiladed
by keeping the natural air
vents clear (see fig. 2) and
by activating the mechanical
aeration device (suction hood
or electric fan fi g. 3 and fi g. 4).
●Intensive and lengthy use
of the appliance may require
additional ventilation. This
can be achieved by opening
a window or by increasing
the power of the mechanical
exhausting system if installed.
●Do not attempt to change the
technical characteristics of
the product because it can be
dangerous.
●If you should not to use
this appliance any more
(or replace an old model),
before disposing of it, make it
inoperative in conformity with
current law on the protection
of health and the prevention
of environmental pollution
by making its dangerous
parts harmless, especially for
children who might play on an
DUAL
MAX EXT
MAX INT
MIN EXT
MAX INT
Fig. 22
abandoned appliance.
●Do not touch the appliance
with wet or damp hands or feet.
●Do not use the appliance
barefoot.
●The manufacturer will not be
liable for any damage resulting
from improper, incorrect or
unreasonable use.
●During, and immediately after
operation, some parts of the
cook top are very hot: avoid
touching them.
●After using the cook top,
make sure that the knob is in
the closed position and close
the main tap of the gas supply
or gas cylinder.
●If the gas taps are not
operating correctly, call the
Service Department.
IMPORTANT:
a l w a y s d i s c o n n e c t t h e
appliance from the gas and
e l e c t r i c i t y m a i n s b e f o r e
carrying out any cleaning
operation.
2) HOT PLATE
It is very important to clean the
surface soon after every use,
when the glass is still tepid.
Do not use metallic sponges,
powder abrasives or corrosive
sprays.
Depending on the dirty level we
recommend:
- slights stains: it is enought the
OFF
MIN INT
MAX INT
use of a moist clean rag.
- Marks of liquid, overfl owed from
the pot, can be removed using
vinegar or lemon.
Periodically wash the hot plate,
the enamelled stell pan support,
the enamelled burner caps "A",
"B" and "C" and the burner
heads "T" (see fi g. 7 and 8) with
lukewarm soapy water. They
should also be cleaned plugs
"AC" and fl ame detection "TC"
(see fi g. 8).
Clean them gently with a small
nylon brush as shown (see fi g.
6) and allow to dry fully.
Do not wash in the dishwasher.
Do not allow vinegar, coffee,
milk, salted water, lemon or
tomato juice from remaining
in contact with the enamelled
surfaces for long periods of time.
WARNINGS:
comply with the following
i n s t r u c t i o n s ,
remounting the parts:
●check that burner head slots
"T" (fi g. 8) have not become
clogged by foreign bodies.
●Check that enamelled burner
cap "A","B","C" (fi g. 7 and 8)
have correctly positioned on
the burner head. It must be
steady.
●The pan support must be
placed in the appropriate
centering pins verifying the
perfect stability.
●Do not force the taps if
they are difficult open or
close. Contact the technical
assistance service for repairs.
●Don't use steam jets for the
equipment cleaning.
CAUTION:
In case of hotplate glass
breakage:
9) Full position
EN
b e f o r e
Closed position
1) Reduced
rate position
Fig. 21
31