Teka JZC Serie Manual De Usuario página 36

EN
Fig. 26
Never heat empty pans, or use
pans with a thin base, as these may
heat up quickly without allowing time
for the automatic disconnection
function of the cooker to come into
operation.
IMPORTANT
RECOMMENDATIONS:
Use vessels with the same base
diameter as that of the cooking zone.
In the cooking zones closest to
the control panel, always keep the
vessels within the cooking marks
indicated on the glass surface and
use vessels of the same or smaller
diameter to these. This will help to
prevent overheating in the control
zone.
Use the rear cooking zones for
intensive use of the appliance. This
will help to prevent overheating of the
control panel.
Do not allow the vessels to invade
the control panel zone, especially
during cooking.
Use and
Maintenance
User instructions of the
Touch Control
HANDLING ELEMENTS (fig. 20 -
page 8)
1 General on/off sensor.
2 Cursor slider for controlling
power.
3 Power and/or residual heat
indicator*.
4 Decimal dot of power and/
of residual heat indicator.
5 Direct access to "Power"
function.
6 Activation sensor for "Block"
function.
36
7 Pilot indicator light "Block"
function activated*.
8 A c t i v a t i o n s e n s o r f o r
"Stop&Go" function.
9 P i l o t i n d i c a t o r l i g h t
" S t o p & G o " f u n c t i o n
activated*.
10 "Minus" sensor for timer.
11 "Plus" sensor for timer.
12 Timer indicator.
13 Decimal dot of the timer.*
14 Activation sensor for
"Synchro" function;
(depending on model).
15 Activation sensor for "Flex
Zone" function; (depending
on model).
16 Activation sensor for "Chef"
functions; (depending on
model).
17 Pilot indicator light "Keep
Warm" function activated*;
(depending on model).
18 Pilot indicator light" Melting"
function activated*;
(depending on model).
19 P i l o t i n d i c a t o r l i g h t
" S i m m e r i n g " f u n c t i o n
activated*; (depending on
model).
20 Pilot indicator light "Quick
Boiling" function activated*;
(depending on model).
21 Pilot indicator light "Slide
Cooking" function activated*;
(depending on model).
22 Pilot indicator light "Grilling"
function activated*;
(depending on model).
23 Pilot indicator light "Pan
Frying" function activated*;
(depending on model).
24 Pilot indicator light "Deep
Frying" function activated*;
(depending on model).
25 Pilot indicator light "Confi t"
function activated*;
(depending on model).
26 P i l o t i n d i c a t o r l i g h t
" P o a c h i n g " f u n c t i o n
activated*; (depending on
model).
* Only visible while running.
The manoeuvres are done by means
of the touch keys. You do not need
to exert force on the desired touch
key, you only need to touch it with
your fi ngertip to activate the required
function
Each action is verifi ed by a beep.
Use the cursor slider (2) to adjust
power levels (0 - 9) by sliding your
fi nger over it. Sliding towards the right
increases the value, whereas sliding
towards the left decreases it.
It's also possible to directly select a
power level by placing your finger
directly on a desired point of the cursor
slider (2)
In order to select a plate on
these models, directly touch the
cursor slider (2).
SWITCHING ON THE DEVICE
1 Touch the On touch key
least one second. The touch control
will become active, a beep will be
heard and the indicators (3) will light
up displaying a "-". If any cooking
area is hot, the related indicator will
fl ash an H.
If you do not take any action in the
next 10 seconds the touch control will
switch off automatically.
When the touch control is activated,
you can disconnect it at any time by
touching the touch button
if it has been locked (lock function
activated). The touch button
always has priority to disconnect the
touch control.
ACTIVATING PLATES
Once the Touch Control is activated
with sensor (1), any plate can be
turned on by following these steps:
1 Slide the finger or touch in any
position of one of the cursors
"slider" (2). The zone has been
selected and simultaneuously the
power level will be set between 0
(1) for at
(1), even
(1)