Publicidad
Idiomas disponibles
Idiomas disponibles
English
Note
If units have individual wheel
adjustment, set all wheels to the
same height.
Model A
Attach the wheels in the position
required.
Model B
Pull the flap and snap into place
in the position required.
Model C
Advance or push back the lever
of the central vertical adjustment
and snap into place in the
position required.
Locking front wheels
(only units with lockable front
wheels)
Fig. 4
Lock wheels to drive straight ahead
– set the wheels in forward position
and put hoop into large hole.
Wheels are freely movable – put
clamp into large hole.
Filling with petrol and checking
oil level
Fill up with lead-free petrol
(see engine manual).
Fill fuel tank up to max. 2 cm
below the lower edge of the inlet
nozzle.
Close fuel tank tightly.
Check oil level and, if required,
top up (see Engine manual).
Clean the battery compartment
on the engine
Remove foreign objects and dirt
from the battery compartment
using a cloth and brush.
Starting the engine
Fig. 5
Danger
!
To prevent injury:
– do not start the engine when
you are standing in front of the
ejector;
– keep hands and feet well away
from the cutting blade;
– never place your hands, feet,
or other parts of the body near
rotating parts; always keep away
from the ejector.
8
All manuals and user guides at all-guides.com
Before starting the engine,
disengage the clutches for all
cutters and drives.
Do not tip the appliance when
starting. Keep the appliance on
an even surface with little or the
shortest possible grass.
Information about the engine
– Observe the information in the
engine manual.
– Some models do not have an
throttle. The engine speed is set
automatically. The engine always
runs at the optimal engine speed.
Insert starter battery into the
battery compartment on the
engine until it engages – Fig. 5A.
Open the fuel tap (if fitted).
Set throttle (if available) to
/max – Fig. 5B.
Stand behind lawn mower –
Press and hold safety hoop –
Fig. 5C.
Turn ignition key on the steering
handle until the engine starts
(start attempt max. 5 seconds,
wait at least 1 minute before the
next attempt) – Fig. 5C.
When the engine is running:
When the engine has started,
push the throttle (if fitted)
between
/max and
to warm up the engine briefly.
Set the throttle to full throttle
(if available).
Note
If you need more information about
operating the engine, please refer
to the engine manual.
Stopping the engine
Fig. 7
Bring throttle (if available) into
position
/min.
Release the safety hoop.
The engine and the cutting tool
stop after a short time.
Operating instructions – Lawn mower with IC engine
Working with the unit
Engaging/disengaging gear
drive
(only in the case of lawn mowers
with gear drives)
Fig. 6A, B, C
Putting gear drive into gear
/
Pull and hold the lever/hoop.
Throwing gear drive out of gear
/
Release lever/hoop.
Information for units according
to Fig. 6C
The unit can be switched on/off
with the left or the right lever or
even with both levers together.
Note
When the unit is pulled back, there
may be increased resistance on the
back wheels on account of the
design. This is not a fault with the
unit but occurs for technical
reasons.
Remedial action (depending on
model): Without pulling the drive
handle, push unit forwards a little,
then backwards.
Changing drive speed of the
wheel drive
/min
(depending on model)
Caution
Damage to the lawn mower
Make adjustments when the engine
is running only.
Model 6D, E
Select from the different speeds
using the small lever (1/min/
and 4/max/
Fig. 6F, G
Select from the different speeds
using the lever (1/min/
4/max/
Note
For technical reasons the speed
may be difficult to change when
the unit is at a standstill.
Remedy: Pull drive bar and select
speed setting.
:
:
).
and
).
Publicidad
