Kärcher HDS 9/20-4 Classic Manual Del Usuario página 13

Control panel
Illustration B
0/OFF = off
Power switch
1
Operating mode: Cold water operation
2
Operating mode: Hot water operation (e = Eco
3
mode, hot water max. 60°C)
Fuel indicator light
4
Symbols on the device
Do not aim the high-pressure jet may at
persons, animals, live electrical equip-
ment or the device itself.
Protect the device against frost.
Danger of injury from electrical voltage.
Only qualified electricians or authorised
and qualified technical specialists are
permitted to work on the electrical sys-
tems.
Health risk from poisonous exhaust gases.
Never inhale the exhaust gases.
Risk of burns from hot surfaces.
Intended use
Only use the device for cleaning, e.g. machines, vehi-
cles, buildings, tools, façades, terraces and garden
equipment.
DANGER
Use at petrol stations or other hazard zones
Risk of injury
Adhere to the respective safety regulations.
Note
Do not allow waste water containing mineral oil to pen-
etrate soil, waterways or the sewage system. Only wash
the motor or the undercarriage in suitable places with an
oil separator.
Water supply limit values
ATTENTION
Dirty water
Premature wear and tear or deposits in the device
Supply the device using only clean water, or recycled
water that does not exceed the specified limit values.
The following limit values apply to the water supply:
● pH value: 6.5-9.5
● Electrical conductivity: Conductivity of fresh water
+ 1200 µS/cm, maximum conductivity 2000 µS/cm
● Settleable particles (sample volume 1 l, settling time
30 minutes): < 0.5 mg/l
● Filterable particles: < 50 mg/l, no abrasive sub-
stances
● Hydrocarbons: < 20 mg/l
● Chloride: < 300 mg/l
● Sulphate: < 240 mg/l
● Calcium: < 200 mg/l
● Total hardness: < 28 °dH, < 50° TH, < 500 ppm
(mg CaCO /l)
3
● Iron: < 0.5 mg/l
● Manganese: < 0.05 mg/l
● Copper: < 2 mg/l
● Active chloride: < 0.3 mg/l
● Free of unpleasant odours
Safety instructions
The following safety instructions apply to the device:
● Observe the respectively applicable national regula-
tions for liquid jet cleaners.
● Observe the respectively applicable national acci-
dent prevention regulations. Liquid jet cleaners must
be tested regularly and the results of the test record-
ed in writing.
● Note that the heating system in the device is classi-
fied as a furnace. Furnaces must be inspected reg-
ularly according to the applicable national
regulations.
● No modifications may be made to the device or ac-
cessories.
Safety devices
Safety devices protect the user and may not be disabled
or functionally circumvented.
● The safety valve opens if the pressure switch is
faulty.
● The safety valve is adjusted and sealed at the facto-
ry. The adjustment is performed only by customer
service.
Water shortage safeguard
● The water shortage safeguard prevents the burner
from switching on when there is a lack of water.
● A sieve prevents the fuse from becoming contami-
nated and must be cleaned regularly.
Exhaust gas thermostat
The exhaust gas thermostat switches the device off
when the emission temperature is too high.
WARNING
Damaged components
Risk of injury
Check that the device, accessories, supply lines and
connections are in perfect condition. If the condition is
not perfect, you may not use the device.
1. Apply the parking brake.
Check the oil level in the high-pressure pump
ATTENTION
Milky oil
Device damage
If the oil is milky, inform authorized Customer Service
immediately.
1. Place the device on a flat and level surface.
2. Check the high-pressure pump oil level at the oil lev-
el display.
The oil level must be in the middle of the oil level in-
dication.
3. Top up the oil if necessary.
Activating the oil tank venting
1. Unscrew the screw plug.
2. Screw in the oil filler plug.
English
Safety valve
Initial startup
13