Removing/Inserting The Battery - Milwaukee 2753-20 Manual Del Operador

ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Attaching and Removing Accessories
1/4" Hex Impact Driver
(Cat. No. 2753-20)
This impact driver is intended for use with
drill and driver bits.
1. To attach an accessory, press the shank
into the hex drive chuck.
2. To remove the accessory, pull out the
ring and remove the accessory. Re-
lease the ring.
Square Drive Impact Wrenches
(Cat. No. 2754-20, 2755B-20)
1. Use only the appropriate size Square Drive
Sockets.
2. To attach a socket, align the accessory with the
anvil and push it firmly over the retaining ring.
3. To remove the accessory, pull the accessory off
the anvil.
Square Drive Impact Wrench with Pin Detent
(Cat. No. 2755-20)
1. Use only the appropriate size Square Drive Sockets.
2. To attach a socket, align the hole in the accessory
with the detent pin on the anvil. Hold the detent
pin in while pushing the socket onto the anvil.
The detent pin will snap into place in the hole to
secure the socket.
3. To remove the socket, insert a nail or other thin
object into the hole in the accessory and press
in the detent pin. Pull the accessory off the anvil.
OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
1. For forward (clockwise) rot-
ation, push the control switch
in the direction shown. Check
the direction of rotation before
use.
2. For reverse (counterclock-
wise) rotation, push the control switch in the
direction shown. Check the direction of rotation
before use.
3. To lock the trigger, push the control switch to the
center position. The trigger will not work when the
control switch is in the locked position.
Always remove the battery pack before performing
maintenance, changing accessories, storing the
tool and any time the tool is not in use.
Selecting Speed
Allow the tool to come to a complete stop before
changing speeds. Press the selector button
cycle between the settings.
Setting
1 2
2753-20 850 2 100 3 000 Designed for driving self-
2754-20 900 1 600 2 500
2755-20
1 700 2 000 2 500
2755B-20
2753-20: The
†
screw stripping, screw breakage, and damage to
the work surface when driving self-tapping screws.
This function is optimized for the most common
materials, including #8-#10 self-tapping screws be-
tween ½"-1" in length and 20-28 gauge sheet metal.
2754-20: The
††
user greater control in application and reduce
damage to the fastener or work surface by auto-
matically shutting the tool off after the tool senses
the mechanism impacting for approximately one
second.
2755-20/2755B-20: The
†††
to give the user greater control in application and
reduce damage to the fastener or work surface
by automatically shutting the tool off after the tool
senses the mechanism impacting for approxi-
mately one second.
4
CENTER TO LOCK
Forward
Max RPM
3
/
tapping screws
in sheet metal
1 600 - tool will shut
off after about one
second of impacting
2 000 - tool will shut
off after about one
second of impacting
function is designed to reduce
function is designed to give the
function is designed
Reverse
to
†
††
†††