Publicidad
Idiomas disponibles
Idiomas disponibles
GB
F
D
DESCRIPTION
70. Positioning Hole
71. Hanger Cap
72. Hole
73. Button
74. Spacer
75. Handle Base
76. Handle Barrier Bar
77. Nuts
78. Bracket
ASSEMBLY
ATTACHING THE POWER HEAD TO THE
TRIMMER ATTACHMENT (Fig. 2)
WARNING
Never attach or adjust any attachment while
power head is running. Failure to stop the engine
may cause serious personal injury.
The trimmer attachment (69) connects to the power head
by means of a coupler (19) device.
Loosen the knob (20) on the coupler of the power
■
head shaft (10) and remove the end cap from the
attachment.
Push in the button located on the trimmer attachment
■
shaft. Align the button with the guide recess (23) on
the power head coupler and slide the two shafts
together.
Rotate the trimmer attachment shaft until the button
■
(73) locks into the positioning hole (70).
Note: If the button does not release completely in
the positioning hole (70), the shafts are not locked
into place.
Slightly rotate from side to side until the button is
■
locked into place.
Tighten the knob securely.
■
WARNING
Be certain the knob is fully tightened before
operating equipment; check it periodically for
tightness during use to avoid serious injury.
REMOVING THE ATTACHMENT FROM THE
POWER HEAD
For removing or changing the attachment:
Loosen the knob.
■
Push in the button and twist the shafts to remove and
■
separate ends.
E
I
P
NL
S
DK
N
FIN
English
ATTACHING THE STORAGE HANGER (Fig. 3)
There are two ways to hang your attachment for storage.
To use the hanger cap (71), push in the button and
■
place the hanger cap over end of the lower end
attachment shaft. Slightly rotate the cap from side to
side until the button locks into place.
The secondary hole (72) in the attachment shaft can
■
be used for hanging purposes as well.
ATTACHING THE HANDLE (Fig. 4)
A barrier handle should be used for ensuring the best
control and maximizing operator safety.
Place the handle base (75) and the bracket (78) on
■
the shaft housing below the spacer (74).
Install the two handle base screws (26) and nuts (77),
■
but do not tighten completely.
Place the front handle (18) grip onto the handle base
■
and install the two screws. Tighten securely.
Adjust the position of the front handle for best
■
balance and comfort.
Tighten the two handle base screws securely.
■
Note: Do not attempt to remove or modify the spacer.
This spacer limits the upper position of the handle grip.
ATTACHING THE SHOULDER STRAP (Fig. 5)
Connect the latch (22) on the shoulder strap (4) to the
■
strap hanger (2).
Adjust the shoulder strap hanger to a balanced
■
position where the blade or cutter attachment will
suspend between 100 mm to 300 mm above the
ground surface.
Adjust the strap hanger to a comfortable position.
■
Note: To quickly release the product from the
shoulder strap, sharply pull the quick release tab (21).
MUFFLER GUARD ASSEMBLY (Fig. 6-7)
Remove muffler guard (27) and two screws (26) from
■
the owner's kits.
Attach the muffler guard to the rear housing (24).
■
Note: Make sure the bent end of the muffler guard (28)
fits securely into the opening of the rear housing (29).
Using the torx wrench supplied (25), install the two
■
screws and tighten securely.
GRASS DEFLECTOR AND BLADE GUARD USE
Note: When converting from brushcutter to string trimmer
or string trimmer to brushcutter, make sure the correct
guard/deflector is being used.
19
GR
H
CZ
RUS
RO
PL
Publicidad
