Publicidad
Idiomas disponibles
Idiomas disponibles
Marks and Symbols on the Instrument
Symbol
Description
This equipment meets the requirements of all
relevant European safety directives. The equipment
carries the CE mark.
This equipment meets the requirements of all
relevant UK Statutory Instruments. The equipment
carries the UKCA mark.
This symbol, on the equipment, indicates that the
user should read the user manual.
This symbol, on the equipment, indicates a warning
and that the user should refer to the user manual.
Ground (Earth)
On/Off
Battery
P1/P2
Identifies the pressure range connector.
Druck is an active participant in the UK and EU
Waste Electrical and Electronic Equipment (WEEE)
take-back initiative (UK SI 2013/3113, EU directive
2012/19/EU).
The equipment that you bought has required the
extraction and use of natural resources for its
production. It may contain hazardous substances
that could impact health and the environment.
In order to avoid the dissemination of those
substances in our environment and to diminish the
pressure on the natural resources, we encourage
you to use the appropriate take-back systems.
Those systems will reuse or recycle most of the
materials of your end life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to
use those systems.
If you need more information on the collection,
reuse, and recycling systems, please contact your
local or regional waste administration.
Please visit the link below for take-back instructions
and more information about this initiative.
https://druck.com/weee
MWP: The maximum working pressure for the connector.
Example: 2 x FS (FS = Full scale pressure).
REFERENCE: The connector is a reference port for
reference pressure only. Refer to "Specification Data" on
page 9.
The identification on each pressure connector includes the
type of thread (1/8 NPT, G1/8...).
Copyright 2003 Baker Hughes Company.
2 | DPI800/802 Instruction Manual–English
1. To Start
1.1 Location of Items
Refer to Figure A1 and Figure A2.
Item
Description
1.
On or Off button.
2.
Left-hand soft-key. Selects the function above
it on the display (Item 24). Example: Edit
3.
Moves back one menu level.
Leaves a menu option.
ESC
Cancels the changes to a value.
4.
Increases or decreases a value.
Highlights a different item.
5.
Holds the data on the display. To continue,
press the HOLD button again.
HOLD
6.
Shows the Select Task menu.
Selects or accepts an item or value.
MENU
OK
Selects [] or cancels [ ] a selection.
7.
Right-hand soft-key. Selects the function
above it on the display (Item 24). Example:
Settings
8.
Display. Refer to Figure A3.
9.
Communications port. Use to connect a
SENSOR/
Universal Measurement Module (UMM) or a
PC
RS 232 cable.
10.
IDOS pressure connector with identification
10a.
marks. Refer to "Safety" on page 1.
Label to identify the pressure range for the
10b.
associated IDOS pressure connector (P1/P2):
Sealed gage (sg), gage (g), absolute (a).
PTFE vent filter or a reference port connector.
10c.
Refer to "Specification Data" on page 9.
11.
Connection point for some of the optional
accessories. Refer to the datasheet.
12.
Battery compartment. Refer to Figure B1.
13., 14., 15.
DPI802/802P only. Terminals to measure
current, to supply 24V source, and to do switch
tests.
1.2 Items on the Display
Refer to Figure A3.
Item
Description
16.
DPI802/802P only. Task indication for the
switch test.
= switch closed.
= switch open.
Task indication for the leak test.
Refer to: Select Task (Table 2 & Table 3).
17.
DPI802/802P only. The loop power supply is
on.
Refer to: Select Task (Table 2 & Table 3).
18.
The measured value satisfies one of the alarm
conditions. Refer to: Settings (Table 4).
19.
The data on the display is on hold. To
continue, press the HOLD button again.
20.
Shows the battery level: 0 ... 100%.
Publicidad
