Jacuzzi sasha 2.0 Manual De Instalación página 26

(detail 4) Re-position the profiles resting against each other
and the shower frame, ensuring that they are fully inserted
under the couplers.
32, details 1-2) Place the silicone on the shower base
(
frame and apply the "L" shaped covers to the base, in the fol-
lowing manner:
- insert them underneath the lip seal of the glazing bead
so that
- they are positioned above the base frame and inside the
metal tank.
Check that they are resting against the front cover (see also
detail 4)
(detail 3) Place the silicone in the contact area between
the "L" shaped covers and the base area.
(detail 4) Also place the silicone in the contact areas be-
tween the "L" shaped cover and the front area.
33, details 1-2) Place a line of silicone on the inner edge of
(
the "U" shaped covers and insert them between the glass panels
and the base frame, as indicated (resting against the front cover).
(detail 3) Place the silicone in the indicated areas.
SAUNA + SHOWER/HAMMAM + SHOWER MODELS:
SAUNA + HAMMAM
34) Fit the upper inner covers, as indicated.
(
35, details 1-2) After having measured the length, cut
(
some sections from the sealant roll which must be applied to the
inner edge of the following profiles:
- the glass panels/the small panels/ (lower, vertical and upper side).
- the glass panels/the large panels/ (lower and upper side).
NOTE: it is recommended to cut approx. 5 cm more of the sealant
than the nominal length and then remove any remaining length
once assembly is complete.
SINGLE MODULES (SAUNA/HAMMAM)
Proceed to the Chapter "Installing roofs".
Installing the shower wall (1)
36) Position the lower wall so that it rests against the base
(
profile and attach it to the frame as indicated.
NOTE: route the equipotential lead upwards, fastening it, in prepa-
ration for subsequent connection.
37, detail 1) Draw the wall towards the mixer system and the
(
wall connections and connect it using the provided flexible pipes.
(detail. 2) route the shower cascade connection pipe upwards, fas-
tening it, in preparation for subsequent connection.
(detail 3) Carry out equipotential connection between the frame
terminal and the mixer system.
38, details 1-2) Carry out connection of the electrical
(
power supply to the indicated junction box; then connect the
display to the indicated cable.
(detail 3) Attach the display to the wall and assemble the cornice.
SAUNA + SHOWER/HAMMAM + SHOWER MODELS:
38, detail 1a) Connect one of the light cables (4) to the
(
cable coming from either the "sauna" or "hammam" module.
SAUNA + SHOWER + HAMMAM MODELS:
38, detail 1a) Connect both of the light cables (4) to
(
the cables coming from the "sauna" and "hammam" modules.
38, detail 4) Layer the wall over the one underneath and
(
attach it as indicated.
Installing roofs
SAUNA/SAUNA + SHOWER/SAUNA + HAMMAM/SAUNA +
SHOWER + HAMMAM MODELS:
39) Apply the metal corners to the roof, as indicated.
(
40, detail 1-2) With models that include installation of
(
the Jacuzzi® remote control system, unwind the sensor cable and
bring it near to the electronic box, as indicated.
40, detail 3) Position the roof so that it rests on the relevant
(
frame. Adjust its position, by lifting it as much as is needed to move
it outwards and close any openings between frame and roof.
40, detail 4) Connect the sensor cable to the terminal in-
(
dicated.
SINGLE MODULES (SAUNA)
Proceed to the Chapter "Benches and duckboards".
HAMMAM/HAMMAM + SHOWER/SAUNA + HAMMAM,
SAUNA + SHOWER + HAMMAM MODELS
41, detail 1) Attach the shower head to the roof.
(
41, detail 2-3) With models that include installation of
(
the Jacuzzi® remote control system, unwind the sensor cable and
bring it near to the electronic box, as indicated.
41, detail 4) Position the roof so that it rests against the
(
respective frame.
Adjust its position, by lifting it as much as is needed to move it
outwards and close any openings between frame and roof.
41, detail 5) Connect the shower head to the hammam's
(
mixing system.
41, detail 6) Connect the sensor cable to the terminal in-
(
dicated.
42) Fix the roof to the walls and apply the cover panels
(
using soft double-sided tape and heat resistant silicone.
26