Jacuzzi sasha 2.0 Manual De Instalación página 24

16a, details 2-3) Install the frame in such a way so the
(
metal dowels are inserted into the panel profile (subsequently,
use a rubber mallet if necessary).
NOTE: these dowels are adjustable so that any positioning errors
can be corrected.
(16a, detail 4) Attach the frame as indicated.
(detail 5) ATTENTION: ensure that you support the
frame until the glass is inserted.
16b, details 1-2) Place a small amount of silicone on
(
the plastic spacers and position them in pairs, as indicated:
- on the lower glass frame,
- on the vertical wall profile,
- on the upper glass frame.
The spacers should be positioned against the wall profiles.
16c, details 1-2) After having measured the length, cut
(
some sections from the sealant roll which must be applied to the:
- bottom glazing bead (f-i)
- vertical glazing bead (f-v)
- top glazing bead (f-s)
NOTE: it is recommended to cut approx. 5 cm more of the sealant
than the nominal length and then remove any remaining length
once assembly is complete.
16c, details 3-4) Position the glass panel on the plastic
(
spacers and allow it to run so that it rests against the spacers
on the vertical profile.
16c, detail 5) Check the spirit level of the upper glass
(
panel (to correct any perpendicularity errors, use spacers with a
different thickness).
16c, detail 6) Install the glazing bead.
(
Installing the wood divider
(only Sauna+Hammam models)
17) Install the indicated profiles on:
(
- the sauna base frame
- the sauna roof frame
- the sauna vertical wall
ATTENTION: do not install the previously removed
profiles.
18, detail 1-2 ) After measuring the length, cut some sec-
(
tions of the sealant roll that must be applied to the bottom glaz-
ing bead (f-i), the vertical glazing bead (f-v) and the top glazing
19).
bead (f-s), see also
NOTE:
- the bottom and upper sealant must be cut so that it is at a distance
of approximately 55 mm from the glass.
- it is recommended to cut approx. 5 cm more of the sealant than the
nominal length and then remove any remaining length once assem-
bly is complete.
(detail 3 ) Install the glass glazing beads (f-i) and (f-v).
19, detail 1) Position the large glass panel on the plastic
(
spacers and allow it to run so that it rests against the spacers on
the vertical profile.
19, detail 2) Check the spirit level of the roof panel (to correct
(
any perpendicularity errors, use spacers with a different thickness).
(detail 3 ) Then install the top glazing bead (f-s).
19a) It is also possible to insert the glass as indicated, instead
(
of making it slide on the spacers.
20, detail 1) Place the silicone on the sauna base frame and
(
apply the "L" shaped cover, in the following manner:
- (detail 2) insert it under the lip seal of the previously installed
glazing bead.
so that
- (detail 3) it is positioned above the base frame and inside the
metal tank.
(detail 4) Reassemble the door glazing bead (top and bottom).
21) Install the covers on the profiles of the base, following
(
the provided instructions.
22, details 1-2-3-4) Insert the wood divider in the sauna
(
base frame,raise the frame from the roof, bring the divider to-
wards the glass and thread the upper end in the roof frame.
(detail 5-6) Check the perpendicularity and that the profile is
aligned with the glass.
22, details 7-8) Move the glass so that a line of silicone
(
can be placed between the divider and the actual glass, across
its entire height.
33, details 1-2) Place a line of silicone on the inner
(
edge of the "U" shaped cover and insert it between:
- the small glass panels and the two base frames,
- the large glass panel and the hammam base, bringing it
so that it rests against the front cover,which has just been
installed.
(detail 3) Place the silicone in the indicated areas.
35, details 1-2) After having measured the length, cut
(
some sections from the sealant roll which must be applied to
the inner edge of the following profiles:
- small glass frames (upper, lower and vertical sides).
- large glass frame (hammam side; upper, lower and vertical
sides).
NOTE: it is recommended to cut approx. 5 cm more of the sealant
than the nominal length and then remove any remaining length
once assembly is complete.
23, details 1-2) Apply the magnetic gaskets, to both the
(
glass and the wood divider, ensuring correct assembly direction.
24