Transport And Storage; Maintenance; Technical Specifications - Tunturi C35 Manual Del Usuario

Ocultar thumbs Ver también para C35:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 43
3.
Upon completion of the measurement, the display
shows the recovery rate as a percentage. The smaller the
rate, the fitter you are. Please note that your results are
in a relation to the pulse level in the beginning of the
measurement, and that your results are personal and
cannot directly be compared with any other person's
results. In order to improve the reliability of recovery
pulse measurement, always try to standardize the
measurement situation as accurately as possible; start
measuring at the same heart rate level as precisely as
possible.
4.
To switch back to the main display by pressing
RESET. The console will also automatically switch to
the main display one minute after the completion of the
measurement.

TRANSPORT AND STORAGE

Please follow these instructions when carrying and
moving the equipment about, because lifting it
incorrectly may strain your back or risk other accidents:
Always switch the power off and unplug the
N O T E !
power cord before you start moving the equipment
around!
The device is easy to move by pushing along on the
integrated transport wheels. Tilt the device from the
front and push along the floor on the wheels at the front
support. We recommend that you use a protective base
when transporting the equipment.
To prevent the equipment malfunctioning, store in a dry
place with as little temperature variation as possible and
protected from dust.

MAINTENANCE

The equipment requires very little maintenance. Check,
however, from time-to-time that all screws and nuts are
tight.
After exercising, clean the equipment with a soft,
absorbent cloth. Do not use solvents. Sweat may cause
corrosion: we recommend therefore that you protect all
metal surfaces outside the plastic covers with teflon.
Never remove the equipment's protective casing.
If the equipment is not used for a period of time, the
transmission belt may become temporarily distorted.
This can lead to a sensation of slightly uneven pedaling.
However, after a few minutes of use the effect disappears
as the belt returns to its original form.
MALFUNCTIONS
Despite continuous quality control, defects and
N O T E !
malfunctions caused by individual components may
occur in the equipment. In most cases it's unnecessary
to take the whole device in for repair, as it's usually
sufficient to replace the defective part. Always give
the model, serial number of your equipment and in
case of malfunctions also conditions of use, nature of
malfunction and any error code.
When you encounter unusual behavior from the device,
simply turn the power off, wait 1 minute and turn the
power on. This should clear incidental errors and ready
O W N E R ' S M A N U A L
the device for normal operation again. If after you have
reset the device by turning the power off and on again,
and the device is still not operational, contact your local
Tunturi dealer for service.
If you require spare parts, always give the model, serial
number of your equipment and the spare part number
for the part you need. The spare part list is at the back
of this manual. Use only spare parts mentioned in the
spare part list.

TECHNICAL SPECIFICATIONS

Length ..........................................135 cm
Width ..........................................66 cm
Height ..........................................157 cm
Weight .........................................63 kg
The C35 meets the requirements of the EU's EMC
Directives on electromagnetic compatibility (89/336/
EEC) and electrical equipment designed for use within
certain voltage limits (73/23/EEC). This product
therefore carries the CE label.
The North American versions (115 V) comply with
FCC requirements on electromagnetic compatibility
and are accordingly marked with the FCC label. The
North American versions also comply with the following
safety standards: UL 1647 and CSA C 22.2 No. 68-92.
The C35 crosstrainer meets EN precision and safety
standards (EN-957).
Due to our continuous policy of product development,
Tunturi reserves the right to change specifications
without notice.
The instructions must be followed carefully in
N O T E !
the assembly, use and maintenance of your equipment.
The warranty does not cover damage due to negligence
of the assembly, adjustment and maintenance
instructions described herein. Changes or modifications
not expressly approved by Tunturi Oy Ltd will void the
user's authority to operate the equipment!
We wish you many enjoyable trainings with your
new Tunturi training partner!
G B
C 3 5
9

Publicidad

Tabla de contenido
loading

Tabla de contenido