Transport And Storage; Maintenance; Technical Specifications - Tunturi C30 Manual Del Usuario

RECOVERY – MEASURING THE RECOVERY
PULSE
Measure your recovery pulse rate at the end of the
workout.
1. To start the measuring of the recovery pulse rate,
press RECOVERY. The display also shows the word
"Recovery".
2. The measuring starts automatically and takes two
minutes.
IMPORTANT! If any disturbances during the measuring
should occur, the display shows "Err" instead of the
measurement value.
3. Upon completion of the measurement, the display
shows the recovery rate as a percentage. The smaller the
rate, the fitter you are. Please note that your results are
in a relation to the pulse level in the beginning of the
measurement, and that your results are personal and
cannot directly be compared with any other person's
results. In order to improve the reliability of recovery
pulse measurement, always try to standardize the
measurement situation as accurately as possible; start
measuring at the same heart rate level as precisely as
possible.
4. To switch back to the main display by pressing
RESET. The console will also automatically switch to
the main display one minute after the completion of the
measurement.

TRANSPORT AND STORAGE

Please follow these instructions when carrying and
moving the equipment about, because lifting it
incorrectly may strain your back or risk other accidents:
The device is easy to move by pushing along on the
integrated transport wheels. Tilt the device from the
front and push along the floor on the wheels at the front
support.
Transport the equipment with extreme caution over
uneven surfaces, for example over a step. The equipment
must never be transported upstairs using the wheels
over the steps, instead it must be carried. Place the
equipment on a firm, level surface, and on a protective
base to avoid any damages to the floor beneath the
equipment. Notice that certain floor materials may
require protection when transporting the equipment.
To prevent the equipment malfunctioning, store in a dry
place with as little temperature variation as possible and
protected from dust.

MAINTENANCE

The equipment requires very little maintenance. Check,
however, from time-to-time that all screws and nuts are
tight.
•
After exercising, clean the equipment with a soft,
absorbent cloth. Do not use solvents. Sweat may cause
corrosion: we recommend therefore that you protect all
metal surfaces outside the plastic covers with teflon.
•
Never remove the equipment's protective casing.
•
If the equipment is not used for a period of time, the
8
All manuals and user guides at all-guides.com
transmission belt may become temporarily distorted.
This can lead to a sensation of slightly uneven pedaling.
However, after a few minutes of use the effect disappears
as the belt returns to its original form.
CHANGING BATTERIES
The console gives a warning signal before the change
of batteries is due. Detach the lid of the battery casing
at the back of the meter and remove the old batteries.
Place the new batteries in the holder (2 x 1.5 V AA) and
push the battery casing lid back into place.
MALFUNCTIONS
Despite continuous quality control, defects and
N O T E !
malfunctions caused by individual components may
occur in the equipment. In most cases it's unnecessary
to take the whole device in for repair, as it's usually
sufficient to replace the defective part. Always give
the model, serial number of your equipment and in
case of malfunctions also conditions of use, nature of
malfunction and any error code.
When you encounter unusual behavior from the device,
simply turn the power off, wait 1 minute and turn the
power on. This should clear incidental errors and ready
the device for normal operation again. If after you have
reset the device by turning the power off and on again,
and the device is still not operational, contact your local
Tunturi dealer for service.
If you require spare parts, always give the model, serial
number of your equipment and the spare part number
for the part you need. The spare part list is at the back
of this manual. Use only spare parts mentioned in the
spare part list.

TECHNICAL SPECIFICATIONS

Length..........................................146 cm
Width ..........................................65 cm
Height..........................................157 cm
Weight .........................................64 kg
The C30 meets the requirements of the EU's EMC
Directives on electromagnetic compatibility (89/336/
EEC) and electrical equipment designed for use within
certain voltage limits (73/23/EEC). This product
therefore carries the CE label.
The C30 crosstrainer meets EN precision and safety
standards (EN-957).
Due to our continuous policy of product development,
Tunturi reserves the right to change specifications
without notice.
The instructions must be followed carefully in
N O T E !
the assembly, use and maintenance of your equipment.
The warranty does not cover damage due to negligence
of the assembly, adjustment and maintenance
instructions described herein. Changes or modifications
not expressly approved by Tunturi Oy Ltd will void the
user's authority to operate the equipment!
We wish you many enjoyable trainings with your
new Tunturi training partner!